Land Pride RCF3696 Скачать руководство пользователя страница 37

Страница: 37 / 76

Section 1: Assembly & Set-Up

RCF3696, RCFM3696, RCF3610, & RCFM3610 Rotary Cutters 326-600M

Table of Contents

8/20/21

5. Remove conical dog pin or bolts (#5) and fastening

hardware (#6) from slip-clutch end of driveline (#14).

6. Slide slip-clutch end of driveline (#14) onto gearbox

input shaft.

Attach slip-clutch end of driveline to gearbox input

shaft with existing conical dog pin or bolts (#5) and

removed hardware (#6). Tighten conical dog pin or

bolts (#5) to 45-50 ft-lb torque.

8. Push/pull on driveline yoke to be sure it is securely

fastened to the gearbox shaft.

9. Rotate access doors (#13) closed and snap in place.
10. Remove rubber protective sleeve (#9) from end of

jackshaft driveline (#14).

11. Fully insert jackshaft driveline (#14) into pillow block

bearing (#11).

12. With locking collar (#2) facing forward, attach pillow

block bearing (#11) to bearing support (#1) with

1/2"-13 x 1 3/4" cap screws (#4), flat washers (#8),

and hex whiz nuts (#7). Tighten nuts to the correct

torque.

13. Rotate locking collar clockwise until tight and then

tighten set screw in locking collar (#2).

14. Attached bolted coupler end of main driveline (#12)

to jackshaft driveline (#14). Push main driveline onto

the jackshaft driveline as far as possible and then

tighten the bolted connection.

NOTE:

Make sure bearing locking collar (#2) is

facing forward toward the tractor.

Constant Velocity Hitch Assembly (RCF3610 Shown)

Figure 1-26

33947

Constant Velocity Driveline (Pull-Type)

The following instructions are for installation of a

“Constant Velocity Driveline”

. Instructions for

“Equal

Angle Driveline”

begin on page 32.

DANGER

To avoid serious injury or death:

•

Make certain driveline yokes are securely fastened at each

end. A loose yoke can work free allowing the driveline to

rotate uncontrollably.

•

Do not use a power take-off adapter. The adapter will

increase strain on the tractor’s power take-off shaft causing

possible damage to shaft and driveline. It will also defeat

the purpose of the tractor’s power take-off shield.

WARNING

To avoid serious injury or death:
Maximum constant velocity driveline turning angle is limited

to 80 degrees Exceeding this angle can cause the driveline to

break and send flying objects.

Refer to Figure 1-26:

1. Remove pillow block bearing (#11) from bearing

support (#1). Keep hardware for reattachment.

2. Attach bearing support (#1) to the deck with

1/2"-13 x 3 3/4" GR5 bolts (#3) and whiz nuts (#7).

Tighten hex whiz nuts to the proper torque.

3. Remove shaft protector (#10) from input shaft of

gearbox (#15).

4. Pry open access doors (#13) in the gearbox shield by

placing a tool in the notch at the back of both doors.

IMPORTANT:

The drivelines must be lubricated

before putting them into service. Refer to

“Lubrication Points”

on page 62.

NOTE:

Bearing support is to be placed in front of

chain/rubber guarding.

Содержание RCF3696













































































Результаты поиска

Содержание RCF3696

Отзывы:

Похожие инструкции для RCF3696

Бренды по названию

Популярные бренды

Land Pride RCF3696, Руководство оператора

Результаты поиска

Содержание RCF3696

Отзывы:

Похожие инструкции для RCF3696

Бренды по названию

Популярные бренды