Land Pride RC4610 страница 32 Скачать руководство пользователя

Страница: 32 / 68

Section 1: Assembly & Set-up

Table of Contents

1/14/19

RC4610 (540 RPM) and RCM4610 (1000 RPM): Rotary Cutters: 334-144M:

Unhook Rotary Cutter

See

“Long-Term Storage”

on page 49 when parking

the cutter for long periods and at end of season.

2. If power take-off is engaged, reduce tractor engine

speed to an idle and then disengage power take-off.

3. Park cutter on a level, hard surface. Place tractor

gear selector in park or set park brake.

4. Wait for blades to come to a complete stop and then

fold wing up to transport position.

5. Shut tractor engine off and remove switch key before

dismounting from tractor.

Refer to Figure 1-28:

6. Remove hairpin cotter (#1) from storage lug (#2).

Refer to Figure 1-29:

Swing transport lock bar (#3) down and place over
lock pin (#4). Secure with hairpin cotter (#1).

Refer to Figure 1-30:

8. Spread stroke control spacers (#2) apart at the break

line and remove them from hydraulic cylinder (#1).

9. Start tractor and lower cutter until front skid shoes

are resting on the ground or on support blocks.

10. Shut tractor down properly before dismounting. Refer

“Tractor Shutdown Procedure”

on page 16.

11. Replace stroke control spacers as needed to support

wheels at this position.

12. Move cylinder lift levers back and forth to release all

hydraulic pressure at the couplers.

Refer to Figure 1-31 on page 29:

13. Remove park jack (#3) from weight box storage

mount and attach to jack mount (#14) as shown.

14. If needed, realign park jack to be vertical. Refer to

“Align Park Jack Vertically”

on page 30.

15. Unhook hitch safety chain (#4) from tractor.

16. Unhook hydraulic hoses (#7) from tractor duplex

outlet. Insert couplers through spring hose loop (#10)
to keep couplers out of the dirt.

17. Unhook wire harness (#17) from tractor outlet. Coil

wire harness and store over spring hose loop (#10)
with connector hanging down to keep moisture out.

18. Pull back on locking collar (#6) and pull driveline (#5)

from tractor power take-off shaft.

19. Collapse driveline (#5) by pushing tractor end of

driveline toward the splitter gearbox.

20. Rotate driveline hanger (#15) up to position shown

and store driveline on hanger.

21. Adjust park jack (#3) to raise cutter up until all load is

removed from tractor drawbar.

IMPORTANT:

The ball detent pin must be fully

inserted into the park jack with ball visible and
popped out on the far side of the jack before working
on or around an unhooked cutter.

Transport Bar, Storage Position

Figure 1-28

Transport Bar, Locked Position

Figure 1-29

Hydraulic Lift Cylinder With Stroke Control Spacers

Figure 1-30

27923

27921

39197

Содержание RC4610





































































Результаты поиска

Содержание RC4610

Отзывы:

Похожие инструкции для RC4610

Бренды по названию

Популярные бренды

Land Pride RC4610, Руководство оператора

Результаты поиска

Содержание RC4610

Отзывы:

Похожие инструкции для RC4610

Бренды по названию

Популярные бренды