Land Pride RC3614 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 66

background image

Table of Contents

©

Copyright 2021 All rights Reserved

Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the

preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use

of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this

product at the time of its publication, and may not reflect the product in the future.

Land Pride is a registered trademark.

All other brands and product names are trademarks or registered trademarks of their respective holders.

Printed in the United States of America.

1/20/21

RC3614 & RCM3614 Rotary Cutters 330-918M

Table of Contents

Important Safety Information . . . . . . . . . . . . . 1

Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . . 1
Look for the Safety Alert Symbol . . . . . . . . . . . . . . . 1
Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Application   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Using This Manual   . . . . . . . . . . . . . . . . . . . . . . . . 14
Owner Assistance  . . . . . . . . . . . . . . . . . . . . . . . . . 14

Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Section 1: Assembly & Set-up . . . . . . . . . . . 15

Tractor Requirements . . . . . . . . . . . . . . . . . . . . . . 15

Horsepower . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Drawbar Set-up . . . . . . . . . . . . . . . . . . . . . . . . . 15

Torque Requirements  . . . . . . . . . . . . . . . . . . . . . . 15
Before You Start  . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Hitch Types  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Hitch Assembly  . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Park Jack Assembly  . . . . . . . . . . . . . . . . . . . . . . . 18
Driveline Assembly  . . . . . . . . . . . . . . . . . . . . . . . . 18
Tractor Shutdown Procedure   . . . . . . . . . . . . . . . . 19
Standard Clevis Hitch Hook-Up . . . . . . . . . . . . . . . 19
LP Performance Hitch Hook-up . . . . . . . . . . . . . . . 20
Bar-Tite Hitch Hook-up  . . . . . . . . . . . . . . . . . . . . . 21
Driveline Hook-up  . . . . . . . . . . . . . . . . . . . . . . . . . 22
Driveline Hanger Adjustment   . . . . . . . . . . . . . . . . 23
Driveline Clearance Check  . . . . . . . . . . . . . . . . . . 23
Hydraulic Hook-up   . . . . . . . . . . . . . . . . . . . . . . . . 24
Rephasing Lift Cylinders & Plumbing   . . . . . . . . . . 24
Wing Folding Cylinder & Plumbing  . . . . . . . . . . . . 24
Remove Shipping Crossbar   . . . . . . . . . . . . . . . . . 25
Unfold Wing Deck  . . . . . . . . . . . . . . . . . . . . . . . . . 25
Relocate Wing Lift Cylinder Mount   . . . . . . . . . . . . 26
Driveline Clearance Check  . . . . . . . . . . . . . . . . . . 27
Purge Hydraulic System  . . . . . . . . . . . . . . . . . . . . 27
Hook-up LED Lights   . . . . . . . . . . . . . . . . . . . . . . . 28
Unhook Rotary Cutter  . . . . . . . . . . . . . . . . . . . . . . 29

Section 2: Adjustments . . . . . . . . . . . . . . . . . 31

LP Performance Hitch Pin Diameter . . . . . . . . . . . 31
Level Cutter Decks . . . . . . . . . . . . . . . . . . . . . . . . 31

Level Center Deck . . . . . . . . . . . . . . . . . . . . . . . 31
Level Wing Deck . . . . . . . . . . . . . . . . . . . . . . . . 32

Adjust Deck Cutting Height . . . . . . . . . . . . . . . . . . 32

Section 3: Operating Instructions . . . . . . . . 33

Startup Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . 33
Avoid Extreme Turning Angles . . . . . . . . . . . . . . . 34

Tractor & Cutter Inspection  . . . . . . . . . . . . . . . . . . 35
Blade Operation Inspection  . . . . . . . . . . . . . . . . . . 35
Transport Lock   . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Transporting   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Road Side Cutting  . . . . . . . . . . . . . . . . . . . . . . . . . 36
Field Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Field Inspection   . . . . . . . . . . . . . . . . . . . . . . . . . 37
Unfold Wing and Set Deck Cutting Height  . . . . . 37
Set Wing Folding Lever In Float Position  . . . . . . 37
Rephasing Out Of Phase Lift Cylinders   . . . . . . . 37
Select Gear Range . . . . . . . . . . . . . . . . . . . . . . . 37
Engage Blades . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Disengage Blades   . . . . . . . . . . . . . . . . . . . . . . . 38

General Operating Instructions . . . . . . . . . . . . . . . 39

Section 4: Options & Accessories . . . . . . . . . 40

Safety Guards  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Tire & Axle Arrangements  . . . . . . . . . . . . . . . . . . . 40
Hitches   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Selector Control Valve Kit  . . . . . . . . . . . . . . . . . . . 40

Section 5: Maintenance & Lubrication . . . . . 41

General Maintenance Information  . . . . . . . . . . . . . 41
Hydraulic System   . . . . . . . . . . . . . . . . . . . . . . . . . 41
Tires   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Skid Shoes   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Cutter Blades   . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Drivelines With Slip Clutches . . . . . . . . . . . . . . . . . 45
Long-Term Storage  . . . . . . . . . . . . . . . . . . . . . . . . 48
Ordering Replacement Parts  . . . . . . . . . . . . . . . . . 48
Lubrication Points  . . . . . . . . . . . . . . . . . . . . . . . . . 49

Axle Hub Bearing  . . . . . . . . . . . . . . . . . . . . . . . . 49
Center Axle Pivots  . . . . . . . . . . . . . . . . . . . . . . . 49
Wing Axle Pivot   . . . . . . . . . . . . . . . . . . . . . . . . . 49
Hitch Frame  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Bar-Tite Hitch (Optional)   . . . . . . . . . . . . . . . . . . 50
Gearbox  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Divider Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Wing Driveline Profile Tubes   . . . . . . . . . . . . . . . 52
Wing Driveline Joints  . . . . . . . . . . . . . . . . . . . . . 52
Intermediate Driveline Joints   . . . . . . . . . . . . . . . 52
CV Main Driveline Profile Tubes . . . . . . . . . . . . . 53
CV Main Driveline Joints   . . . . . . . . . . . . . . . . . . 53

Section 6: Specifications & Capacities  . . . . . 55
Section 7: Features & Benefits   . . . . . . . . . . . 57
Section 8: Troubleshooting  . . . . . . . . . . . . . . 58
Section 9: Torque & Tire Inflation Charts  . . . 59
Section 10: Warranty   . . . . . . . . . . . . . . . . . . . 60

«
1
2
3
4
5
...
»

Содержание RC3614



































































Отзывы:

Нет отзывов

Похожие инструкции для RC3614

Бренд: MacDon Страницы: 84

Бренд: MacDon Страницы: 89

Бренд: Patton electronics Страницы: 18

Бренд: Bahco Страницы: 9

Бренд: Raven Страницы: 17

Бренд: Campbell Страницы: 12

Бренд: Tabi Страницы: 8

Бренд: Dabi Atlante Страницы: 102

Sportsound SSR-300

Бренд: Daktronics Страницы: 42

Varycolor MICRO 150HTI

Бренд: JB-Lighting Страницы: 18

Бренд: Latham Страницы: 4

Бренд: SafeWaze Страницы: 23

Бренд: Teac Страницы: 44

Бренд: Te Pari Страницы: 6

FUSION APOLLO MS-WB675

Бренд: Garmin Страницы: 18

Бренд: Rapid Shape Страницы: 12

MultiFill 003-561-005

Бренд: Hanskamp Страницы: 20

CIRCOLINA G10q T9

Бренд: Life Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды