Land Pride RC3614 Скачать руководство пользователя страница 24

Страница: 24 / 66

Section 1: Assembly & Set-up

Table of Contents

RC3614 & RCM3614 Rotary Cutters 330-918M

1/20/21

LP Performance Hitch Hook-up

DANGER

To avoid serious injury or death:
A crushing hazard exists while hooking-up and unhooking the

implement. Keep people and animals away while backing-up

to the implement or pulling away from the implement. Do not

operate hydraulic controls while a person or animal is directly

behind the power machine or near the implement.

WARNING

To avoid serious injury or death:
The ball detent pin must be fully inserted into the park jack

with ball visible and popped out on the far side of the jack

before working on or around an unhooked cutter.

Refer to Figure 1-12:

1. Make certain park jack (#3) is properly attached to

cutter hitch and secured with ball detent pin (#8).

2. If clevis hitch (#9) is not already supported

horizontal, rotate clevis horizontal and flip hitch

holder (#12) up so that its holes are on top as shown.

3. Insert customer-supplied hitch pin (#1) through holes

in hitch holder (#12) as shown in detail A. Secure with

hairpin cotter (#2).

4. Store center 3-point link in its storage hook.
5. Start tractor, raise 3-point arms fully up, and carefully

back tractor within close proximity of clevis (#9).

6. Shut tractor down properly before dismounting. Refer

“Tractor Shutdown Procedure”

on page 19.

NOTE:

Hitch pin (#1) and hairpin cotter (#2) are

customer-supplied.

Verify tractor drawbar is adjusted correctly. Refer to

“Drawbar Set-up”

dimensions on page 15.

8. Raise or lower park jack (#3) to align clevis (#9) with

tractor drawbar. Drawbar should fit between lower

and upper plates of clevis.

9. Restart tractor and continue to back tractor up to

cutter hitch until hitch holes in tractor drawbar and

hitch clevis (#9) are aligned.

10. Shut tractor down properly before dismounting.
11. Remove bushings in clevis if customer supplied hitch

pin diameter is larger than 1". See

“LP Performance

Hitch Pin Diameter”

on page 31 for instructions.

12. Remove hairpin cotter (2) and hitch pin (#1) from

hitch holder (#12) and rotate hitch holder down.

13. Attach cutter to tractor drawbar with hitch pin (#1) and

hairpin cotter (#2) as shown in detail B.

14. Lower park jack (#3) until cutter hitch weight is

supported by tractor drawbar.

15. Remove park jack (#3) from hitch and attach it to the

weight box storage base with ball detent pin (#8).

Make sure base is level with or lower than the head.

See cover picture for correct positioning.

16. Attach hitch safety chain (#4) to the tractor. Adjust

chain length to remove all slack except what is

necessary to permit turning. Lock chain hook

securely to the safety chain.

17. Continue with

“Driveline Hook-up”

on page 22.

IMPORTANT:

Before moving the cutter, relocate

protect park jack by attaching it to the weight box.

Make sure the jack is stored with its base level or

lower than the head to prevent water and freeze

damage.

LP Performance Hitch Hook-up

Figure 1-12

37998

37298

Содержание RC3614



































































Результаты поиска

Содержание RC3614

Отзывы:

Похожие инструкции для RC3614

Бренды по названию

Популярные бренды

Land Pride RC3614, Руководство оператора

Результаты поиска

Содержание RC3614

Отзывы:

Похожие инструкции для RC3614

Бренды по названию

Популярные бренды