Land Pride RC3614 Скачать руководство пользователя страница 25

Страница: 25 / 66

Section 1: Assembly & Set-up

Table of Contents

RC3614 & RCM3614 Rotary Cutters 330-918M

1/20/21

Bar-Tite Hitch Assembly to Tractor Tongue

Figure 1-13

Bar-Tite Hitch Hook-up

Attach Bar-Tite Hitch to Tractor Drawbar

Refer to Figure 1-13:

1. Insert 1" x 5 1/2" hex bolt (#1) through hitch top

plate (#2), hitch bushing (#3), hitch wear plate (#4),

tractor drawbar (#5), and washer (#6) as shown.

Secure with 1" locknut (#7). Tighten 1" locknut snugly

to remove all play and then back nut

one-quarter turn.

Do Not

torque 1" locknut.

2. Insert two 3/4" x 6" GR5 hex bolts (#8) through,

3/4" flat washers (#9), hitch top plate (#2), hitch wear

plate (#4), and formed hitch support (#10) as shown.

Secure with 3/4" locknuts (#11).

3. Tighten 3/4" locknuts to correct torque.
4. Remove 1" x 6 1/2" GR5 hex bolt (#12) and 1" lock

nut (#13) from hitch bushing (#3). Keep bolt and

locknut for reuse.

Attach Bar-Tite Hitch to Rotary Cutter

DANGER

To avoid serious injury or death:
A crushing hazard exists while hooking-up and unhooking the

implement. Keep people and animals away while backing-up

to the implement or pulling away from the implement. Do not

operate hydraulic controls while a person or animal is directly

behind the power machine or near the implement.

WARNING

To avoid serious injury or death:
The ball detent pin must be fully inserted into the park jack

with ball visible and popped out on the far side of the jack

before working on or around an unhooked cutter.

22265

Bar-Tite Hitch Hook-up

Figure 1-14

Refer to Figure 1-14:

1. Make certain park jack (#3) is properly attached to

cutter and secured with ball detent pin (#8).

2. Store center 3-point link in the tractor’s storage hook.
3. Start tractor, raise 3-point arms fully up, and carefully

back tractor within close proximity of clevis (#9).

4. Shut tractor down properly before dismounting. Refer

“Tractor Shutdown Procedure”

on page 19.

5. Verify tractor drawbar is adjusted correctly. Refer to

“Drawbar Set-up”

dimensions on page 15.

6. Raise or lower park jack (#3) to align hitch (#11) with

bolt hole in swivel clevis (#9).

Restart tractor and continue to back tractor up to

cutter hitch until hole in hitch bushing (#11) aligns

with holes in swivel clevis (#9).

8. Shut tractor down properly before dismounting.
9. Insert 1" x 6 1/2" GR5 hex bolt (#1) through swivel

clevis (#9) and hitch bushing (#11). Secure hex bolt

with locknut (#2). Tighten locknut snugly to remove

all play.

Do Not

torque 1" locknut.

10. Lower park jack (#3) until cutter hitch weight is

supported by tractor drawbar.

11. Remove park jack (#3) from hitch frame and attach it

to the weight box storage base with ball detent

pin (#8). Make sure base is level with or lower than

the head especially after the wing is folded up. See

cover picture for correct positioning.

12. Attach hitch safety chain (#4) to tractor. Adjust chain

length to remove all slack except what is necessary

to permit turning. Securely lock chain hook to the

safety chain.

13. Continue with

“Driveline Hook-up”

on page 22.

33870

IMPORTANT:

Before moving the cutter, relocate

protect park jack by attaching it to the weight box.

Make sure the jack is stored with its base level or

lower than the head to prevent water and freeze

damage.

Содержание RC3614



































































Результаты поиска

Содержание RC3614

Отзывы:

Похожие инструкции для RC3614

Бренды по названию

Популярные бренды

Land Pride RC3614, Руководство оператора

Результаты поиска

Содержание RC3614

Отзывы:

Похожие инструкции для RC3614

Бренды по названию

Популярные бренды