Land Pride RC2512 Series Скачать руководство пользователя страница 42

Страница: 42 / 60

Section 5: Maintenance & Lubrication

RC2512 Series 2 S/N Rotary Cutters 330-725M

10/7/21

Table of Contents

2. Disconnect main driveline from tractor power take-off

and secure cutter deck in the up position with solid

supports before servicing underside of cutter.

Refer to Figure 5-1:

3. Remove rubber plug (#5) above cutter blade (#6).

Rotate blade bolt (#1) until in alignment with access

hole (A).

4. Unscrew locknut (#3) to remove cutting blade (#6).

Blade bolt (#1) is keyed and will not turn freely.

5. Both blades should be sharpened at the same angle

as the original cutting edge and must be replaced or

re-ground at the same time to maintain proper

balance in the cutting unit. The following precautions

should be taken when sharpening blades:
a. Do not remove more material than necessary.
b. Do not heat and pound out a cutting edge.
c. Do not grind blades to a razor edge. Leave a blunt

cutting edge approximately 1/16" (2 mm) thick.

d. Always grind cutting edge so end of blade remains

square to cutting edge and not rounded.

e. Do not sharpen back side of blade.
f. Both blades should weigh the same with not more

than 1 1/2 oz. difference. Unbalanced blades will

cause excessive vibration which can damage

gearbox bearings and create structural cracks.

Refer to Figure 5-2:

6. Carefully check cutting edges of blades in relation to

blade carrier rotation to ensure correct blade

placement. Cutter blades must be installed with

cutting edge leading in rotation

Refer to Figure 5-1:

WARNING

To avoid serious injury or death:
Locknuts can lose their ability to lock properly once removed.

Always use a new locknut when installing blades.

7. Insert blade bolt (#1) through blade (#6),

dishpan (#4), and flat washer (#2). Secure blade with

new locknut (#3)

and torque locknut to 450 ft-lbs

(610 Nm).

8. If replacing dishpan (#4), nut (#7) on gearbox output

shaft should be torqued to 450 ft-lbs (610 Nm)

minimum and secured with cotter pin (#8) with both

legs bent opposite directions around the nut.

9. Replace rubber plug (#5).
10. Reconnect main driveline to tractor power take-off

shaft.

IMPORTANT:

Examine blade bolts and their flat

washers for excessive wear and replace if worn.

Cutter Blade Assembly

Figure 5-1

Blade Rotation

Figure 5-2

30628

Use 1-11/16"

Socket Wrench

On Blade Nut #3

Blade Bolt Kit & Dishpan Part No’s.

Item Part No.

Part Description

318-586A BLADE BOLT KIT (Item No’s 1, 2, & 3)

)

802-277C BLADE BOLT 1 1/8-12 x 3 7/16 WITH KEY

804-147C WASHER FLAT 1 HARD ASTMF436 PN

803-170C NUT HEX TOP LOCK 1 1/8-12 PLATE

DISHPAN (See Parts Manual for Part No.)

840-273C PLUG LP 3" ID RUBBER

820-198C CUTTER BLADE 1/2 x3x25 CCW (CTR Deck)

820-437C CUTTER BLADE 1/2 x3x19 CCW (LH Wing)

820-438C CUTTER BLADE 1/2 x3x19 CW (RH Wing)

CCW

Содержание RC2512 Series





























































Результаты поиска

Содержание RC2512 Series

Отзывы:

Бренды по названию

Популярные бренды

Land Pride RC2512 Series, Руководство оператора

Результаты поиска

Содержание RC2512 Series

Отзывы:

Бренды по названию

Популярные бренды