Land Pride RC2512 Series Скачать руководство пользователя страница 36

Страница: 36 / 60

Section 3: Operating Instructions

RC2512 Series 2 S/N Rotary Cutters 330-725M

10/7/21

Table of Contents

Unfold Wings

Refer to Figure 3-4:

DANGER

To avoid serious injury or death:
Keep everyone away from the cutter when folding or unfolding

the wings or when raising or lowering the cutter. The cutter

can pinch or crush a person when performing these

operations.

1. Inspect blade carriers for locked blades prior to

lowering the wings. Separate locked blades.

Wing Deck Blade Positioning

Figure 3-4

Refer to Figure 3-3 on page 30:

2. Start tractor and raise both wings up to release any

tension on transport locks (#3).

3. Without lowering cutter, shut tractor down properly

before dismounting. Refer to

“Tractor Shutdown

Procedure”

on page 14.

4. Remove hairpin cotters (#1) from both left and right

wing cylinder pins (#4).

Refer to Figure 3-2 on page 30:

5. Rotate end of transport locks (#3) up to storage

lugs (#2). Secure with hairpin cotters (#1).

6. Start tractor and lower both wings down.

Set Blade Cutting Height

Adjust cutter to field cutting height. See

“Adjust Cutter

Height”

on page 26 for detailed instructions.

Place Wing Folding Lever In Float Position

Use the float position of your tractor’s hydraulic system to

provide automatic floating of the wings for varying terrain

conditions. This will ensure that the wing gauge wheels

are in continuous contact with the ground at all times.

37530

Wing Deck
Cutting Blades

Blade Carrier

IMPORTANT:

The wing folding levers should be in

float position to avoid damage to the wing hydraulic

cylinders and axles while cutting on uneven terrain.

IMPORTANT:

Do not let the wings flex down more

than 20 degrees while operating the cutter. Doing so

can cause damage to the cutter.

Select Gear Range

Optimum ground speed depends on density of material

being cut, horsepower rating of tractor, and (in some

cases) terrain. Always operate tractor at cutter’s full-rated

power take-off speed in a gear range that allows the

cutter to make a smooth cut without lugging the tractor

down, usually between 2 to 5 mph. Loss of power take-off

speed will allow the blades to hinge back and result in

ragged, uneven cutting.

Engage Blades

1. Select a gear range that will allow the cutter to make

a smooth cut without lugging the tractor down.

See

“Select Gear Range”

on page 32 for detailed

instructions.

2. With wings lowered, increase throttle to a speed just

enough to get the cutter started without stalling

tractor while slowly engaging power take-off

drivelines. Use tractor’s power take-off soft start

option if available.

3. Ensure all drivelines are rotating and that the cutter is

not vibrating excessively after ramping up to 540

power take-off speed for at least 3 seconds. If

excessive vibration continues after 3 seconds at full

540 power take-off speed, disengage power take-off

immediately, shut down tractor, and remove switch

key. Wait for blades to come to a complete stop

before dismounting tractor.

4. Investigate the cause if cutter was shut down due to

excessive vibration. See

“Blade Operation

Inspection”

on page 29 for detailed instructions.

5. If cutter was not shut down, commence forward

cutting operation at full power take-off operating

speed. Make a new gear selection if tractor is lugging

down or if cutter is making a rough cut.

6. Frequently inspect cutter for loose bolts and nuts.

Tighten all loose hardware as indicated in the

“Torque Values Chart”

on page 54.

Disengage Blades

1. Slowly decrease throttle speed until engine idle

speed is reached.

2. Disengage power take-off.
3. Stay on the tractor until the blades have come to a

complete stop. Always place tractor in park or set

park brake, shut tractor engine off, and remove

switch key before dismounting.

IMPORTANT:

Cutter blades can lock-up against

each other during start-up and shut-down,

especially if tractor’s power take-off engagement is

“INSTANT ON” and/or “INSTANT OFF”. Follow Blade

Engagement and Blade Disengagement instructions

to help eliminate blade lock up.

Содержание RC2512 Series





























































Результаты поиска

Содержание RC2512 Series

Отзывы:

Бренды по названию

Популярные бренды

Land Pride RC2512 Series, Руководство оператора

Результаты поиска

Содержание RC2512 Series

Отзывы:

Бренды по названию

Популярные бренды