background image

Section 1: Assembly & Set-Up 

Table of Contents

11/5/19

PFL20, PFL30, PFLE45, PFLE55, & PFL(E)64 Series Plate Mounted Pallet Forks 319-038M

9

Fork Installation

Figure 1-1

35796

Notched Opening

Pin Notches

Section 1: Assembly & Set-Up

Fork Installation

Refer to Figure 1-1:

CAUTION

!

To avoid minor or moderate injury:  
A pinching hazard exists when installing forks. Do not place 

hands or fingers between carrying bars and forks. 

1. Raise handle of fork locking pin (#1) straight up.
2. Center upper end of fork (#2) on upper carrying 

bar (#3). Make sure retaining hook (A) is caught 

behind upper carrying bar (#3) and retaining 

hook (B) fits in notched opening in lower carrying 

bar (#4).

3. Slide fork to the right by pushing on the fork near 

carrying bars (#3 & #4) until locking pin (#1) is 

positioned over one of the pin notches.

4. Lower locking pin handle (#1) to seat pin in the 

selected notch. Make sure locking pin is seated and 

retaining hooks “A” & “B” are secured behind the 

carrying bars.

5. Repeat steps 1-4 for the second fork, but slide the 

second fork to the left.

Step Relocation

Refer to Figure 1-1:

The pallet fork is shipped from the factory with step (#7) 

mounted on the right-hand side of the frame as shown. If 

preferred, the step can be moved from the right-hand 

side to the left-hand side.
1. Remove flange lock nuts (#5), carriage bolts (#6) and 

step (#7) from mounting holes "C". 

2. Attach step (#7) to mounting holes "D" with existing 

carriage bolts (#6) and flange lock nuts (#5). Make 

sure the surface with 12 grip points on the step are 

facing up. 

3. Tighten flange lock nuts (#5) to the correct torque for 

5/16"-18 GR5 bolts.

Skid Steer & Tractor Hook-Up

DANGER

!

To avoid serious injury or death:  
A crushing hazard exists while hooking-up and unhooking the 

attachment. Do not allow anyone to stand between attachment 

and power machine while approaching or backing away from 

the attachment. Do not operate lift and/or tilt controls while 

someone is near the power machine and/or attachment.

WARNING

!

To avoid serious injury or death:  
Lightweight power machines may need weight added to the 

rear to maintain steering control and prevent forward tipping 

or side tipping caused by a heavy front load. Consult your 

power machine Operator’s Manual to determine proper 

weight requirements and maximum weight limitations.

Содержание PFL 2042





























Отзывы: