Land Pride PD15 Series, Руководство оператора

Страница: 27 / 50

Section 3: Operating Instructions
Table of Contents
PD10, PD15, PD25 & PD35 Post Hole Diggers 317-048M 8/9/19
23
2. If needed, a slow moving vehicle sign can be
purchased from your nearest Land Pride dealer.
Refer to
“Slow Moving Vehicle Sign Accessory” on
page 34.
Unhook Post Hole Digger
Refer to Figure 3-2:
1. If using Land Pride’s Storage Stand, skip to “Unhook
Post Hole Digger with Storage Stand” on page 23.
If not, continue with step 2 on page 23.
2. Lower auger tip to the ground. Shut tractor engine off
and remove key before dismounting from the tractor.
3. Lower auger tip onto level hard ground. Place tractor
in park or neutral and set park brakes. Turn tractor
engine off, and remove switch key before
dismounting from the tractor.
4. Always chock tractor wheels for an extra measure of
safety should the tractor be parked on a gentle slope.
5. Make sure the Post Hole Digger is secured with solid
supports & bracing so that it cannot fall over while
unhooking the unit.
6. Pull back on driveline pull collar (#5) and hold while
pulling driveline yoke from the tractor power take-off
shaft.
7. Store yoke end of driveline off the ground to keep the
universal joint and pull collar out of the dirt.
8. Unhook boom from the tractor’s 3-point center hitch.
Keep hitch pin and retaining pin for reuse.
9. Pull lower 3-point linchpins (#2) and pull 3-point lift
arms off of yoke hitch pins (#1). Lower yoke and
boom onto the ground or onto stable support blocks.
Keep linchpins for reuse.
10. Once the Post Hole Digger is disconnected and
3-point lift arms are clear, drive tractor away being
careful not to catch on the Post Hole Digger.
Unhook Post Hole Digger with
Storage Stand
Refer to Figure 3-3:
WARNING
!
To avoid serious injury or death:
Do not disconnect post hole digger from the tractor on a steep
slope. Injury to personnel and implement may result.
1. Lower auger tip onto level hard ground. Place tractor
in park or neutral and set park brakes. Turn tractor
engine off, and remove switch key before
dismounting from the tractor.
NOTE: It is easier to unhook and hook-up to the
Post Hole Digger if it is supported upright. Land
pride offers an accessory storage stand to aid in
storing, unhooking, and hooking up the Post Hole
Digger. See
“Storage Stands” on page 32.
2. Always chock tractor wheels for an extra measure of
safety should the tractor be parked on a gentle slope.
3. Attach storage stand (#6) to cradle (#5). Make
certain guide slots at end of storage stand (#6) are
securely positioned over cradle pins (#1).
4. Secure storage stand (#6) to cradle (#5) with
knobs (#8). Screw knobs on tight.
Refer to Figure 3-2 on page 22:
5. Pull back on driveline pull collar (#5) and hold while
pulling driveline yoke from the power take-off shaft.
6. Store yoke end of driveline (#4) off the ground to keep
universal joint and pull collar out of the dirt.
7. Unhook the boom (#3) from the tractor’s 3-point
center hitch holes. Keep hitch pin and retaining pin
for reuse.
Refer to Figure 3-3:
8. Without starting the tractor, lower yoke hitch pins (#2)
into support angles (#5) as follows:
a. Loosen knobs (#9) and adjust support angles (#4)
to align with yoke hitch pins (#2).
b. Tighten knobs (#9).
c. Lowering 3-point arms until yoke hitch pins (#2)
are supported in storage angle brackets (#4).
9. Pull lower 3-point linchpins and 3-point lift arms from
yoke hitch pins (#2). Keep linchpins for reuse.
10. Once the Post Hole Digger is disconnected and
3-point lift arms are clear, drive tractor away being
careful not to catch on the digger or storage stand.
Unhook Post Hole Digger With Storage Stand
Figure 3-3
NOTE: There may be some lowering and lifting of
3-point lift arms to properly position hitch pins (#2) in
storage brackets (#4). Also, storage brackets may
need to be raised, lowered, or flipped around to
properly align with hitch pins (#2).
GUIDE
SLOTS
35778