Land Pride MPS2607 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 78

background image

16

Section 1: Assembly & Set-up

MPS2607, MPS2609, & MPS2611 Multi-Purpose Seeder 329-301M

Table of Contents

8/8/23

Tow Hitch Option

Refer to Figure 1-7:

Hydraulic cylinder (#7), cylinder mount (#12), and
mounting hardware (#17, #18, & #19) are shipped stored
on weight tray (#20). Spacer (#15) is attach to the top
center clevis for shipping purposes only.

1.

Remove hardware (#13, #14, & #16) from the top
center clevis. Discard spacer (#15).

2.

Attach cylinder (#7) and top link mount (#12) to the
center clevis hitch with existing 3/4"-10 x 4 GR5 bolts
(#16 & #19), lock washers (#14, & #18), and nuts
(#13 & #17). Tighten nuts to the correct torque.

3.

Attach hitch (#1) to lower 3-point clevises with hitch
pins (#6). Secure hitch pins with linchpins (#4).

4.

Remove detent pin (#12) and rotate park jack (#11) in
jack mount “A” until near vertical. Fully insert detent
pin (#12) through park jack and park jack mount.

5.

Extend or retract park jack (#11) until rod end of
hydraulic lift cylinder (#7) is in align with hole “B” in
the hitch lug.

6.

Insert clevis pin (#5) and secure with flat washer (#2)
and cotter pin (#3). Bend one or more legs of cotter
pin to keep pin from falling out.

IMPORTANT:

Do not raise spike rollers off the

ground with park jack (#11).

Tow Hitch Option Assembly

Figure 1-7

73356

7.

Coil hydraulic hoses (#8 & #9) and wire
harness (#10). Store coiled loops on the seeder.

Acremeter Option

Refer to Figure 1-8 on page 17:

1.

Remove upper guard (#26) as follows:

a. Remove bolt (#15), lock washer (#21), flat

washer (#20), hand knobs (#25) and guard (#26).

b. Set guard (#26) and attaching hardware

(#15, #20, #21, & #25) aside for reuse later.

2.

Remove lower guard (#6) as follows:

a. Remove bolts (#15), flat washers (#21), and

guard (#6).

b. Set guard (#6) and attaching hardware

(#15 & #21) aside for reuse later.

3.

Loosen nut (#18) securing idler sprocket (#24) and
remove roller chain (#28).

4.

Loosen nut (#18) securing idler sprocket (#2) and
remove roller chain (#27).

NOTE:

Refer to

“Electronic Acremeter (Option)”

on page 56 and instruction manual no. 194-074M for
detailed programming and operating instructions.

NOTE:

Keep greasable pivot bolt (#7) and all-seeds

drive sprocket with lockout clutch (#5) together.

«
...
18
19
20
21
22
...
»

Содержание MPS2607















































































Отзывы:

Нет отзывов

Похожие инструкции для MPS2607

Бренд: PROFAX Страницы: 28

Бренд: New Holland Страницы: 21

Бренд: New Holland Страницы: 31

T30 HydroSeeder SD

Бренд: Finn Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды