Land Pride FDR2572, Руководство оператора

Страница: 16 / 34

Section 1: Assembly & Set-Up
Table of Contents
FDR2572 & FDR2584 Rear Discharge Grooming Mowers 310-262M 11/6/18
12
Check Collapsible Length
Figure 1-5
Check Driveline Collapsible Length
Refer to Figure 1-5:
1. Make sure driveline is installed properly to the mower
gearbox input shaft and tractor power take-off shaft
before checking driveline collapsed length. Refer to
“Driveline Hook-up to Gearbox” and “Driveline
Hook-up to Tractor” on page 11.
2. With driveline level, measure 1" ( “B” dimension)
back from universal joint shield to end of outer
driveline shield as shown in Figure 1-5.
a. If measurement is less than 1", shorten driveline.
a. If measurement is 1" or more, skip to “Check
Maximum Allowable Length” on page 12.
Shorten Driveline
Refer to Figure 1-5:
1. Unhook driveline from tractor power take-off shaft
and gearbox shaft.
2. Raise 3-Point arms until mower gearbox shaft and
tractor power take-off shaft are approximately level
with each other.
3. Support mower deck at this height with support jacks
or support blocks to keep power take-off and gearbox
shafts level while shorting the driveline.
4. Place gear selector in park, set park brake, shut
tractor off and remove switch key.
5. Pull driveline apart as shown in Figure 1-5.
6. Attach outer driveline universal joint to tractor power
take-off shaft and inner driveline universal joint to
mower gearbox shaft. Pull on each driveline section
to be sure universal joints are properly secured.
22009
IMPORTANT: A driveline that is too long can bottom
out causing structural damage to the tractor and
implement. Always check driveline minimum length
during initial setup, when connecting to a different
tractor, and when alternating between using a quick
hitch and a standard 3-point hitch. More than one
driveline may be required to fit all applications.
7. Hold driveline sections parallel to each other. The
inner and outer shields on each section should end
approximately 1" short of reaching universal joint
shield on the adjacent section (see
“B” dimensions).
8. If driveline sections are too long, measure 1"
( “B” dimension) back from universal joint shield and
make a mark at this location on the inner and outer
driveline shields.
9. Cut-off inner driveline shield at measured mark
(“ X ” dimension). Cut same amount off inner driveline
profile (“ X1 ” dimension).
10. Repeat cut-off procedure (“ Y ” & “ Y1 ” dimensions) on
the outer driveline section.
b. Remove all burrs and cuttings.
Check Maximum Allowable Length
Figure 1-6
Check Maximum Allowable Length
Refer to Figure 1-6:
Make sure driveline collapsible length is checked first.
See
“Check Driveline Collapsible Length” on page 12.
Driveline maximum allowable length, when fully
extended, must have a minimum overlap of profile tubes
by not less than 1/2 the free length with both inner and
outer profile tubes being of equal length. Determine the
maximum allowable length as follows:
1. Unhook driveline from tractor and Grooming Mower.
Pull outer and inner drivelines apart.
2. Measure and record “Free Length” of inner and
outer profiles as shown in Figure 1-6.
3. Move driveline halves together until profile tubes
overlap by 1/2 the “Free Length”. For future reference,
measure and record
“Maximum Allowable Length”
as shown in Figure 1-6.
Record Maximum Allowable Length here: ________
4. Reattach inner driveline yoke to gearbox shaft and
outer driveline yoke to tractor's power take-off shaft.
5. The driveline should now be moved back and forth to
ensure that both ends are secured. Reattach any end
that is loose.
24804
Outer Shielding has been removed for clarity.