Land Pride AFM4211 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 42

Land Pride AFM4211 Скачать руководство пользователя страница 32

30

Section 5: Maintenance & Lubrication

AFM4211 All Flex Grooming Mower 315-507M

4/12/11

Table of Contents

4-Way Gearbox

Unscrew top plug to remove dipstick (#1). Wipe oil from
dipstick and screw dipstick back in without tightening.
Unscrew dipstick and check oil level on dipstick. If oil is
near the bottom of the dipstick or below the dipstick, add
recommended gear lube through the top plug hole until oil
reaches top mark on dipstick. Reinstall top plug with
dipstick and tighten.

Type of Lubrication: Gear Lube EP 80-90W

Quantity = Fill until oil reaches full mark on dipstick.

IMPORTANT: Do not overfill with oil! Unit should be
level when checking oil. Oil expands when hot,
therefore, always check oil level when cold. Take your
gearbox to a Land Pride dealer if it requires service.

Mower Deck Gearbox

Method 1: Unscrew top plug to remove dipstick (#1). Wipe
oil from dipstick and screw dipstick back in without
tightening. Unscrew dipstick and check dipstick. If oil level
is at or below the bottom level mark, add recommended
gear lube through top plug hole until oil reaches top mark
on dipstick. Reinstall top plug with dipstick and tighten.

Method 2: Remove side oil plug (#2). If oil is below bottom
of plug hole, add recommended gear lube through top
dipstick hole until oil flows out of side plug hole. Reinstall
and tighten side oil plug (#2) and vented dipstick (#1).

Type of Lubrication: 80-90W EP Gear Lube

Quantity = Fill until oil reaches top mark on dipstick or
begins to flows out side plug hole in gearbox.

IMPORTANT: Do not overfill with oil! Unit should be
level when checking oil. Oil expands when hot,
therefore, always check oil level when cold. Take your
gearbox to a Land Pride dealer if it requires service.

As

Required

26575

Do Not Overfill

As

Required

30215

Do Not Overfill

«
...
30
31
32
33
34
...
»

Содержание AFM4211











































Отзывы:

Нет отзывов