background image

Assembly Instructions 

#380-152A & #380-336A Installation Instructions Manual No. 380-153M   

7/26/22

6

Loader Hose Loop Bracket

Figure 10

Hydraulic Hose Routing

Refer to Figure 1 on page 2, Figure 8, & Figure 9 on 
page 5
, & Figure 10:

1. Route hoses (#9) along loader arm and through 

loader hose loop bracket “F” to the third function 

valve (#10).

2. Slide black dust plug (#29) on free end of 

hose (#9A)and connect female coupler (#24) to the

hose.

3. Slide green dust plug (#30) on free end of hose (#9B) 

and connect female coupler (#24) to the hose.

4. Connect (#9A) hose to quick coupler (#11) in port “A” 

on valve block (#10).

5. Connect (#9B) hose to quick coupler (#11) in port “B” 

on valve block (#10).

6. Secure hydraulic hoses (#9) as needed with 

cable ties (#3).

9

F

37121

Check Operating and Fluid Level

The Third Function Valve is now ready to be used with a 

multitude of attachments. Be sure to familiarize yourself 

with a complete understanding of how to operate the 

Third Function Valve Kit. 

DANGER

!

To avoid serious injury or death:  
Do not allow bystanders to be near the attachment, loader 

arms, or tractor during operation. They can become 

entangled, pinched, or crushed by the equipment. Disconnect 

and lockout power source before making adjustments or 

servicing tractor and attachment. 

1. Hook attachment to the tractor front loader and 

couple hydraulic hoses to the bulkhead couplers at 

the front of the loader. 

2. Raise attachment off the ground and operate the third 

function hydraulics using the push-buttons on the 

newly installed control handle.

The top red button switch will actuate the 
attachment in one direction.

The bottom red button switch will actuate the 
attachment in the opposite direction.

3.

Refer to Figure 1 on page 2: 

Switch hoses (#9) at 

couplers (#11) if the attachment’s hydraulic 

cylinder(s) operate in the opposite direction 

intended.

4. Once hoses and cylinder(s) are full of hydraulic fluid, 

check tractor hydraulic fluid level.

5. If low, add recommended hydraulic fluid.

Relieve Hydraulic System Pressure

Be sure to lower the attachment to the ground and to 

relieve all hydraulic pressure to the attachment before 

leaving the tractor seat. Relieve hydraulic pressure to the 

attachment as follows: 
1. Turn tractor switch key to off. 
Press and hold both red buttons down on the control 

handle until all movement at the attachment stops.

IMPORTANT:  

Refer to your tractor Operator’s 

Manual for recommended hydraulic fluid and 

procedure for checking hydraulic fluid level.

Содержание 380-152A















Отзывы: