lancer TOUCHPOINT SERIES 4800T Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 42

background image

2.7 ICE CHUTE CLEANING

It is recommended to perform this procedure monthly, or more often if desired. Use the

cleaning solution described above. An alternate solution of one part water to one part vin-

egar may be used to remove water spots and calcium deposits.

A. Turn off power to the dispenser.

B. Remove Merchandiser.

C. Remove Ice Chute Lever, then remove Splash Plate Assembly by lifting it up and out from the

dispenser face. NOTE: Always remove the ice chute lever before removing the splash plate.

D. Remove clip from Auger Motor Shaft. Remove four (4) screws from brackets. Ensure Motor

Harness is disconnected and retain the auger shaft key.

F. Remove the Ice Chute Assembly base by removing the four (4) screws that attach it to the unit.

G. Prepare the Cleaning Solution described in Section 3.1.

H. Soak the Ice Chute Assembly in the solution.

I. Rinse and dry the Ice Chute Assembly thoroughly.

J. Reinstall the Ice Chute Assembly.

K. Reinstall Merchandiser and Splash Plate.

L. Reconnect power to the dispenser.

2.8 REMOVAL OF ICE CHUTE FOR SERVICE

A. Disconnect power to the dispenser

B. Remove the merchandiser.

C. Disconnect the wire harness for the auger motor.

D. Remove the C-clip from the auger shaft.

E. Support the auger motor. Remove four (4) screws securing the auger motor mounting plate.

F. Slide the motor off the auger shaft. Do NOT discard the shaft key.

G. Remove the two (2) auger motor mounting plate support brackets by removing the four (4)

screws securing brackets to the mounting plate.

H. Unhook the ice chute spring from the ice chute.

I. Remove the ice chute assembly from the mounting plate by removing the screws securing it

into place.

J. Be sure to retain the o-ring from between the ice chute assembly and the feed-through.

K. Remove the outer ice chute from the base by pushing the hinge tabs inward to release the

outer ice chute.

24

«
...
22
23
24
25
26
...
»

Содержание TOUCHPOINT SERIES 4800T











































Отзывы:

Нет отзывов

Похожие инструкции для TOUCHPOINT SERIES 4800T

Бренд: Garantia Страницы: 2

Бренд: Zip Страницы: 12

Бренд: WaterCare Страницы: 7

Sanitizer Plus ASP1-1044

Бренд: Water Right Страницы: 30

Бренд: Bras Страницы: 20

Бренд: Curtis Страницы: 21

Бренд: IBC Water Страницы: 33

GCH 503520 B12 TSR

Бренд: TESY Страницы: 24

LavAdvantage SPEX012240T

Бренд: EemaX Страницы: 16

Бренд: Cimm Страницы: 2

Бренд: Frigidaire Страницы: 21

Бренд: Zojirushi Страницы: 15

Бренд: Ariston Страницы: 112

Бренд: Crystal Mountain Страницы: 47

Бренд: Murdock Страницы: 10

Бренд: Black & Decker Страницы: 24

Бренд: Black & Decker Страницы: 54

Бренд: Black & Decker Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды