Lancaster 7-LXCT-1 Скачать руководство пользователя

Страница: 1 / 24

PAGE 1

In the event that you need assistance for servicing your water filter, please first contact the

professional contractor who installed the system.

Congratulations on purchasing your new

Lancaster Water Filter

. This unit is designed to give you

many years of trouble free service. For servicing and future inspection purposes, please file this

booklet with your important documents.

ELECTRONIC WATER FILTER WITH THE

X-FACTOR CONTROL VALVE

INSTALLATION, OPERATING AND

SERVICE MANUAL

WATER FILTERS AND NEUTRALIZERS

ACID NEUTRALIZERS

  7-LXDAN-1
  7-LXDAN-1.5
  7-LXDAN-2
  7-LXDAN-3

IRON FILTER

  7-LXIM-1
  7-LXIM-2
  7-LXIM-3

COLOR, TASTE, ODOR

  7-LXCT-1
  7-LXCT-2
  7-LXCT-3

SEDIMENT/ TURBIDITY

  7-LXST-1
  7-LXST-2
  7-LXST-3

AERATION-SULFUR & IRON

  7-LXCTAIR-1
  7-LXCTAIR-2
  7-LXCTAIR-3

AERATION-IRON ONLY

  7-LXIMAIR-1
  7-LXIMAIR-2
  7-LXIMAIR-3

Содержание 7-LXCT-1

























Результаты поиска

Содержание 7-LXCT-1

Отзывы:

Похожие инструкции для 7-LXCT-1

Бренды по названию

Популярные бренды

Lancaster 7-LXCT-1, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание 7-LXCT-1

Отзывы:

Похожие инструкции для 7-LXCT-1

Бренды по названию

Популярные бренды