background image

“twister” 2111 Media Converter      23

Warranty and Servicing

Limited Lifetime Warranty for Lancast Media Converters
Lancast, Inc. warrants that every Lancast media converter product purchased
after April 30, 1999, will be free from defects in material and workmanship
for its lifetime. This warranty covers the original user only and is not
transferable. Should the unit fail at any time during this warranty period,
Lancast will, at its sole discretion, replace, repair, or refund the purchase
price of the product. This warranty is limited to defects in workmanship and
materials and does not cover damage from accident, acts of God, neglect,
contamination, misuse or abnormal conditions of operation or handling,
including overvoltage failures caused by use outside of the product’s
specified rating, or normal wear and tear of mechanical components.

To establish original ownership and provide date of purchase, please
complete and return the registration card or register the product on-line at
www.lancast.com. This warranty will not go into effect until the warranty
registration has been received by Lancast.

To return a defective product for warranty coverage, contact Lancast
Customer Service for a return materials authorization (RMA) number. Send
the defective product postage and insurance prepaid to the address provided
to you by the Lancast Technical Support Representative. Failure to properly
protect the product during shipping may void this warranty. The Lancast
RMA number must be clearly on the outside of the carton to ensure its
acceptance.

Lancast will pay return transportation for product repaired or replaced in-
warranty. Before making any repair not covered by the warranty, Lancast
will estimate cost and obtain authorization, then invoice for repair and return
transportation. Lancast reserves the right to charge for all testing and
shipping costs incurred, if test results determine that the unit is without
defect.

This warranty constitutes the buyer’s sole remedy. No other warranties, such
as fitness for a particular purpose, are expressed or implied. Under no
circumstances will Lancast be liable for any damages incurred by the use of
this product including, but not limited to, lost profits, lost savings, and
incidental or consequential damages arising from the use of, or inability to
use, this product. Authorized resellers are not authorized to extend any other
warranty on Lancast’s behalf.

Содержание 2111-15-012111-15-02 / 2111-16-01 / 2111-16-02 / 2111-18-01 / 2111-18-02

























Отзывы: