Lamtec LT2 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 105

Lamtec LT2 Скачать руководство пользователя страница 34

4

Technical

Description

32

4.8.1 Parameters of digital inputs

Idle state

Here you can set the idle state of the digital input. If the state differs from the one set
here, the actions predefined for the functions (A, B, C, D) are executed. If Diagnostic
mode is set here, the functions (A, B, C, D) can be initiated for the corresponding
digital input by means of the State parameter.

•

LOW (normal open contacts)

• HIGH

(idle)

• Diagnostic

mode

Functions A,B,C,D

The four functions are very similar in structure, but the assignment of the limit values
LV 1 - 4 or fuels to the individual functions

(A, B, C, D) is limited. Reset limit value 1 and Fuel 1 are only possible with function A;
Reset limit value 2 and Test gas 2 only with function B, etc.

The following actions are possible:
• None
•

Offset calibration

Initiates offset calibration.

•

Fault reset

Acknowledges present faults.

•

Warning reset

Acknowledges present warnings.

•

Reset LV 1

(Function A) resets limit value 1, functions B, C and D

reset

the limit values 2, 3 and 4 respectively.

Therefore, the corresponding LVs must be set to

Acknowledge” in Reset mode

• Fuel 1

(Function A only) selects fuel 1, functions B, C and D

select fuels 2, 3 and 4 respectively.

• Probe 1

(Function A) selects probe 1, functions B, C and D

select probes 2, 3 and 4

•

No

cal.

Calibration

disabled

•

PID controller On/Off If the PID controller option is enabled, here you can

switch off the PID controller.

•

Maintenance

Switches the device to “Maintenance”

•

Deactivate

Limit value x (also see section 4.13)

State

This parameter indicates the state of the digital input. The three possible states are
inactive (idle state) and active; the set functions (A, B, C, D) are initiated. The state of
the digital input can be set manually with this parameter, provided that the idle level
parameter is set to

Diagnostic mode

.

Parameters:
1175/1185/1195/1205/
1215/1225/1235/1245

Parameters:
1170/1180/1190/1200/
1210/1220/1230/1240

Parameters:
1171….1244

«
...
32
33
34
35
36
...
»

Содержание LT2










































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды