LaMotte Tracer PockeTester Скачать руководство пользователя страница 11

Страница: 11 / 12

Unstable readings

Insufficient electrolyte

in probe. Air bubbles

visible when probe

inverted.
Electrolyte is depleted

Replace electrolyte, and

membrane cap assembly

Readings drift down Insufficient

stirring

Stir sample with meter or move

probe in sample

Slow response

Dirty or damaged

membrane

Replace electrolyte and

membrane cap

Electrode can not be

calibrated

Depleted electrolyte
Dirty or damaged

membrane

Replace electrolyte and

membrane cap

Electrode can not

be calibrated after

replacing electrolyte

and membrane cap

Dirty probe.
Cathode is not a shiny

gold color.

Clean cathode with cleaning

cloth or cleaning paper. Do not

over polish.

Sample reading is

frozen

Meter is in HOLD mode
Meter is locked

Release HOLD by momentarilly

pressing

MODE

button.

Remove batteries. Press

ON/

OFF

button. Replace batteries

and press

ON/OFF

button.

Stored readings will be lost.

MAINTENANCE

Battery Replacement

1. Twist off the battery compartment cover.
2. Holding the battery housing in place with a finger, pull out the

battery carrier using the two small tabs.

3. Replace the four (4) CR2032 batteries observing proper

polarity.

4. Replace the battery carrier, reattach the battery

compartment cap and tighten securely.

Battery Safety

Dispose of batteries responsibly; observe local, state,

and federal regulations.

Never dispose of batteries in a fire; batteries may explode or leak.

Never mix battery types; install new batteries of the same type.

Electrode Replacement

1. Turn the meter OFF. Turn the electrode retaining collar clock-wise and

remove it.

www.

.com

[email protected]

1.800.561.8187

Содержание Tracer PockeTester













Результаты поиска

Содержание Tracer PockeTester

Отзывы:

Похожие инструкции для Tracer PockeTester

Бренды по названию

Популярные бренды

LaMotte Tracer PockeTester, Руководство пользователя

Результаты поиска

Содержание Tracer PockeTester

Отзывы:

Похожие инструкции для Tracer PockeTester

Бренды по названию

Популярные бренды