Laminex Metaline Скачать руководство пользователя

Страница: 9 / 24

X - 6mm

Y - 6mm

X - 6mm

Back Face

Front Face

Y - 6mm

Back Face

Front Face

X + 6mm

Back Face

Front Face

Y + 6mm

Back Face

Front Face

X - 6mm

Y - 6mm

Back Face

Double Sided Tape

Front Face

X + 6mm

Y + 6mm

Back Face

Front Face

Back Face

Front Face

X + 6mm

Y + 6mm

Back Face

Front Face

Double Sided Tape

X - 6mm

Y - 6mm

X - 6mm

Back Face

Front Face

Y - 6mm

Back Face

Front Face

X + 6mm

Back Face

Front Face

Y + 6mm

Back Face

Front Face

X - 6mm

Y - 6mm

Back Face

Double Sided Tape

Front Face

X + 6mm

Y + 6mm

Back Face

Front Face

Back Face

Front Face

X + 6mm

Y + 6mm

Back Face

Front Face

Double Sided Tape

Some core must remail in routered

channel (maximum 1mm)

3.1.1 Fabrication Type – Folded Internal Corners

Preferred Method:

For fabrications where the Metaline is folded into the corner of the kitchen with a
90° seamless fold (as opposed to the traditional glass method of 2 sheets being
butted together), the following sequence is observed:

X - 6mm

Y - 6mm

X - 6mm

Back Face

Front Face

Y - 6mm

Back Face

Front Face

X + 6mm

Back Face

Front Face

Y + 6mm

Back Face

Front Face

X - 6mm

Y - 6mm

Back Face

Double Sided Tape

Front Face

X + 6mm

Y + 6mm

Back Face

Front Face

Back Face

Front Face

X + 6mm

Y + 6mm

Back Face

Front Face

Double Sided Tape

Some core must remail in routered

channel (maximum 1mm)

X - 6mm

Y - 6mm

X - 6mm

Back Face

Front Face

Y - 6mm

Back Face

Front Face

X + 6mm

Back Face

Front Face

Y + 6mm

Back Face

Front Face

X - 6mm

Y - 6mm

Back Face

Double Sided Tape

Front Face

X + 6mm

Y + 6mm

Back Face

Front Face

Back Face

Front Face

X + 6mm

Y + 6mm

Back Face

Front Face

Double Sided Tape

1. Measure the internal dimensions

of the corner:

2. Allowance is made for the panel

fold in the measurement as per
below:

3. Panels are routed using a 90° V

bit behind the section to be fold
to allow for the panel to be bent,
giving the following finished fold:

4. The installed section will look like:

Содержание Metaline

























Результаты поиска

Содержание Metaline

Отзывы:

Похожие инструкции для Metaline

Бренды по названию

Популярные бренды

Laminex Metaline, Руководство пользователя

Результаты поиска

Содержание Metaline

Отзывы:

Похожие инструкции для Metaline

Бренды по названию

Популярные бренды