manualshive.com logo in svg

Lakeside 000010, Инструкции по сборке и использованию

Поделиться
Скачать
Lakeside 000010 Скачать руководство пользователя страница 3

Shore Ramp DIY Kit     p/n: 000010 rev A 

3 

doc: 400010 copyright© 2022 Lakeside Recreation, LLC 

Mark & Drill the 2x6 Sides to Connect the Plates 

Hold (clamp) the End Roller Plate aligned with the edges of its outer sides even with the end of the 2x6 Side and the 
bottom surface aligned with the bottom inner edge of the 2x6 Side.  Use a square to ensure the plate is square with the 
bottom of the 2x5 Side.  Mark the 3/8” holes and also trace the location of the elliptical 5/8” hole on the inner face of 
the 2x6 Side.  Unclamp and drill the 3/8” Holes from the inside face of the 2x6 Sides.   

For the Strut Mount Plate, hold (clamp) the 2x6 Side to the angled side of the plate, aligned with the front end of the 2x6 
Side and the bottom surface aligned with the bottom inner edge of the 2x6 Side.  Use a square to ensure the plate is 
square with the bottom of the 2x5 Side .  Mark the holes on the inside face of the 2x6 Side.  Unclamp and Drill the 3/8” 
Holes from the inside face of the 2x6 Sides.  Repeat for the other side.   

   

 

 

In addition, use the ¾” drill bit to make a clearance pocket ¾” deep on each inside face where the 5/8” elliptical hole is 
located.  Angle the drilling to approximately match the angle of the shaft that will be inserted.  Repeat for the other Side.  
Check the clearance with the shaft and both sides. 

To locate the Lateral Plate, measure 8-½” from the front edge of the 2x6 Side and make a mark.  Using a square to mark 
a square line will aid with alignment.  Align the Lateral Plate front edge (the angled tongue faces to the front) to the 
marked line.  Align the bottom of the plate to the bottom edge of the 2x6 Side.  Mark the holes.  Drill the 3/8” Holes 
from the 

inside

 face.  Repeat for the other Side. 

   

 

   

Содержание 000010









Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды