Lakeside 000010 Скачать руководство пользователя страница 1

Страница: 1 / 8

Shore Ramp DIY Kit p/n: 000010 rev A

Shore Ramp DIY Wood Kit
Assembly & Use Instructions

p/n: 000010

Lakeside Recreation LLC

www.shoreramp.com

Additional Materials Needed

The Shore Ramp DIY Kit is designed to be assembled using pressure-treated lumber purchased separately by the
customer from a local lumber yard or home improvement store such as Home Depot, Menards, Lowes, etc.
The Kit uses the following quantities and sizes of pressure-treated lumber:

QTY

Size

Length

2x6

12’

2x4

6’

(cut into two 3’ pieces)

4x4

4’

(likely need to purchase 8’ and cut)

Tools Needed

The following tools will be necessary or useful to fabricate and assemble the Shore Ramp DIY Kit.



Wood Saw with blade suitable for cross cutting the 2x4’s, the 4x4, and the angled rip cuts in the 2x6’s:



3/8” Drill Bit, 3/4” Drill Bit, 1-1/8” Drill Bit (Spade style recommended)



Drill



Drill-Guide or a Drill-Press (recommended for uniform, precisely-bored holes).



9/16” box 9/16” socket wrench.



Rubber mallet.



Medium to large pliers with good gripping teeth (linesman’s pliers recommended).



Measuring Tape



Marking Pencil & Straight edge



Square



Clamps



Belt Sander or hand Sanding Block with course sandpaper

Содержание 000010









Результаты поиска

Содержание 000010

Отзывы:

Бренды по названию

Популярные бренды

Lakeside 000010, Инструкции по сборке и использованию

Результаты поиска

Содержание 000010

Отзывы:

Бренды по названию

Популярные бренды