Laird BTM511 страница 33 Скачать руководство пользователя

Страница: 33 / 46

www.lairdtech.com

Laird Technologies

BTM510/511

Bluetooth

Multimedia Module

CONFIgurINg

THE BTM510/511

3.1.5 Send remote control command

AT+AVC<operation_id

hex

>,<button_state>

Send a remote control command to a connected AVRCP target. Internally, a PASS

THROUGH command is created and sent to the PANEL subunit of the AVRCP target.

<operation_id

hex

> is the value for the actual remote control command. Valid values are

specified in Table 3 8. Some Operation IDs can be replaced by mnemonics, see Table 3 8.

<button_state> represents “Button pushed” (=0) or “Button released” (=1)

If <button_state> is not specified, two PASS THROUGH commands, each with

button_state=0 and button_state=1 will be created and sent consecutively.

The “OK” response is sent immediately on receipt of AT+AVC command. On command

completion, an unsolicited message will be sent to the host in the form “AVPTC n

<bd_addr> <button_state>”. AVPTC means “AVrcp Pass Through Confirmation”.

Parameter n indicates the command status:

‘n’=0: successful, command confirmation received from target

‘n’=1: timeout, target has not sent confirmation within the specified maximum time

‘n’=2: all other unsuccessful outcomes

Parameters:

<operation_id

hex

(mandatory):

see Table 3 8

<button_state>

(optional) :

‘0’ - Button pushed

‘1’ - Button released

Response:

<cr,lf>OK<cr,lf> (immediately)

And:

<cr,lf>AVPTC n <operation_id

hex

> <button_state><cr,lf>

(after command completion)

If status n indicates an unsuccessful outcome,<operation_id

hex

> and <button_state>

are omitted.

3.2 AVRCP – Target (TG)

This section describes AT Commands and S registers when BT-MM is configured as an AVRCP

Target (S301=2). In this mode, BT-MM supports one subunit PANEL (see [5]).

3.2.1 Incoming AVRCP Connection Request

An incoming AVRCP connection request is accepted automatically if a valid link key for

the paging device exists. If no link key is available, Secure Simple Pairing (SSP, BT2.1)

or legacy pairing (BT2.0 or earlier) is carried out, depending on the Bluetooth Version

of the paging device.

After an AVRCP connection has been established, the module remains in AT command

mode. S Register 531 is ignored for AVRCP connections.

3.2.2 UNIT INFO Response

It is mandatory to respond to a UNIT INFO command if configured as AVRCP target.

Required response parameters are IEEE Company ID and a Unit Type.

The IEEE Company ID is a 24 bit integer which can be set via new S register 303.

In the current revision of BT-MM firmware, subunit “Panel” (=0x09) will be returned

always. Values of unit/subunit types are outlined in Table 3 9.

3.2.3 SUBUNIT INFO Response

It is mandatory to respond to a SUBUNIT INFO command if configured as AVRCP target.

Required response parameters are Subunit type and MaxSubUnitId.

Subunit type will always be returned as 0x09 (Panel).

MaxSubUnitId will always be returned as 0x00 (only one subunit exists, which is panel)

Содержание BTM511















































Результаты поиска

Содержание BTM511

Отзывы:

Похожие инструкции для BTM511

Бренды по названию

Популярные бренды

Laird BTM511, Руководство пользователя

Результаты поиска

Содержание BTM511

Отзывы:

Похожие инструкции для BTM511

Бренды по названию

Популярные бренды