manualshive.com logo in svg

laguna PS2, Руководство пользователя

Поделиться
Скачать
laguna PS2 Скачать руководство пользователя страница 4

 

 

4 

1. Warnings:

 

Those responsible for this machine must take care that all operators who works with this 
machine have read this instruction book and understand how to operate the machine safely and 
in a correct way. 

1- Read and understand the Operating Manual. 

2- All workers must wear the appropriate clothes and personal protection, such as safety  glasses. 

3- Never wear loose-fitting clothes near the machine. 

4- Workers with long hair must use hair net or cap. 

5- Never use jewels and rings when operating the machine. 

6- The machine must always be positioned on a strong, level surface. If the machine has casters then 

be sure they are locked before starting operating. 

7- Check the electrical voltage, it must be 220 V +/- 5 %.  if the power is more than the 5 % +/-, this can 

damage the electric/electronic components and is not covered by the warranty!! 

²

 

Note:

  When  using  the  machine,  please  make  sure  you  stand  in  front  of  machine,  brush 

rotation is “down” rotation. Avoid standing in the wrong positions, which can be dangerous. 

 

          

          Figure 1: 

Содержание PS2

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды