4
Safety
REVO 1216 Lathe © 2018 Laguna Tools 10/22/2018
Sa
fe
ty
EN
Table A
Ampere Rating
Volts
Total length of cord in feet
120
25
50
100
150
240
50
100
200
300
More Than
Not More Than
Minimum gage for cord
0
6
18
16
16
14
6
10
18
16
14
12
10
12
16
16
14
12
12
16
14
12
Not Recommended
GROUNDING INSTRUCTIONS
1.
All grounded, cord-connected tools:
In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current
to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-
grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly
installed and grounded in accordance with all local codes and ordinances.
Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a qualified
electrician.
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The
conductor with insulation having an outer surface that is green with or without yellow stripes is the
equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not
connect the equipment-grounding conductor to a live terminal.
Check with a qualified electrician or service personnel if the grounding instructions are not completely
understood, or if in doubt as to whether the tool is properly grounded.
Use only 3-wire extension cords that have 3-prong grounding plugs and 3 pole receptacles that accept the
tool's plug.
Repair or replace damaged or worn cord immediately.
2.
Grounded, cord-connected tools intended for use on a supply circuit having a nominal rating less than 150
volts:
This tool is intended for use on a circuit that has an outlet that looks like the one illustrated in Sketch A in Fig.
1. The tool has a grounding plug that looks like the plug illustrated in Sketch A in Fig. 1. A temporary adapter,
which looks like the adapter illustrated in Sketch B and C, may be used to connect this plug to a 2 pole
receptacle as shown in Sketch B if a properly grounded outlet is not available. The temporary adapter should
be used only until a properly grounded outlet can be installed by a qualified electrician.
This adapter is not
permitted in Canada.
The green-colored rigid ear, lug, and the like, extending from the adapter must be
connected to a permanent ground such as a properly grounded outlet box.
3.
Grounded, cord-connected tools intended for use on a supply circuit having a nominal rating between 150 –
250 volts, inclusive:
This tool is intended for use on a circuit that has an outlet that looks like the one illustrated in Sketch D. The
tool has a grounding plug that looks like the plug illustrated in Sketch D. Make sure the tool is connected to
an outlet having the same configuration as the plug. No adapter is available or should be used with this tool.
If the tool must be reconnected for use on a different type of electric circuit, the reconnection should be
made by qualified service personnel; and after reconnection, the tool should comply with all local codes and
ordinances.
Fig X001: Grounding Methods Provided by CSA Group. (A) Receptacle with nominal rating less than 150 volts. (B) 150 volt
receptacle without grounding pin fitted with adapter. (C) Grounding receptacle adapter. (D) Receptacle with nominal rating
between 150 - 250 volts.
LOCKING THE LATHE
Fig L006 - Method of locking the Laguna Revo Lathe. (1) Constructed 3 side box with padlock holes. (2) Padlocks.
It is strongly recommended that the lathe is never left unattended in the unlocked condition.To lock the machine it
is recommended that a cover (not supplied) is constructed according to the supplied concept displayed in Fig
L006.
PROPOSITION 65 WARNING OF HARMFUL EXPOSURE
Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains
chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals
are:
Lead from lead-based paint.
Crystalline silica from bricks, cement, and other masonry products.
Arsenic and chromium from chemically treated lumber.
Your risk of exposure varies, depending on how often you do this type of work. To reduce your exposure to these
chemicals, work in a well-ventilated area and work with approved safety equipment, such as face or dust masks
that are specifically designed to filter out microscopic particles.