7
SAW FEATURES
The use of any accessory or attachment or performance of any operation with this tool other than
those recommend in this instruction manual may present a risk personal injury.
4
5
6
8
11
1
2
3
9
10
7
12
1.
On/Off Trigger Switch
2.
On/Off Trigger Switch Lock
3.
Grip Handle
4.
Water Cock Valve
5.
Water Hose Inlet
6.
Blade Height Lock
7.
Blade Height Guide
8.
Blade Fence
9.
Blade Cover
10.
Blade Arbor Nut
11.
Bevel Guide
12.
Bevel Lock
NOTE:;OLWHY[UHTLZHUKWHY[U\TILYZJVYYLZWVUK[V[OVZL\ZLKPU[OL
(ZZLTIS`6WLYH[PVUZHUK4HPU[LUHUJLZLJ[PVUZVM[OPZTHU\HS
UNPACKING
Prior to tool assembly and use, read
this manual thoroughly to familiarize
yourself with proper assembly, maintenance and safety
procedures.
Check shipping carton and machine for damage before
unpacking. Lay out all parts on a piece of cardboard
or other clean, flat surface. Always check for and
remove protective shipping materials around motors
and moving parts. Do not discard shipping carton and
packing materials until you have carefully inspected the
contents, assembled the machine and are satisfied that
it operates correctly.
Compare package contents to Component Parts List
and Hardware Package List prior to assembly to make
sure all items are present. Carefully inspect parts to
make sure no damage occurred during shipping. If any
parts are missing, damaged or preassembled, do not
assemble. Instead, call Service Center at 1-800-850-2044
for assistance.
CALIFORNIA PROPOSITION 65
This product and some dust created
by power sanding, sawing, grinding,
drilling, and other construction activities may contain
chemicals, including lead, known to the State of
California to cause cancer, birth defects, or other
reproductive harm.
Wash hands after handling.
Some examples of these chemicals are:
s Lead from lead-based paints
s Crystalline silica from bricks and cement and other
masonry products
s Arsenic and chromium from chemically-treated
lumber
Your risk from exposure to these chemicals varies
depending on how often you do this type of work
To reduce your exposure, work in a well-ventilate
area and with approved safety equipment, such a
dust masks that are specially designed to filter ou
microscopic particles. Avoid prolonged contact with
dust from power sanding, sawing, grinding, drilling
and other construction activities. Wear protectiv
clothing and wash exposed areas with soap and water.
6
7
UNPACKING
B1
B2
B3
B4
B5
B6
B7
H1
H2
ASSEMBLY
ATTACH THE BLADE FENCE
1. Install the wear-plate wedge clips (H2) as
shown in Figure 5.
2. Attach the wing screws (H1) but do not
tighten.
3. Carefully insert the blade fence (8, B5) so that
the ends of the fence arms slide under the
wedge clips.
NOTE:
The blade fence may be inserted and
used upside down or right side up.
When used right side up, the bottom lip of the
fence is lower than the bottom plate of the saw,
enabling you to use the edge of your workpiece
as a guide.
When installed upside down, the bottom of the
fence is level with the bottom plate of the saw,
keeping the bottom plate level to the workpiece
while letting you use any perpendicular surface
as a guide.
4. Tighten the wing screws but do not
overtighten.
FIGURE 5
H2
H1
B5
NOTE:
The part and hardware names and numbers correspond to those used in Saw Features on page 6
and the Shipping Contents on page 7.
SHIPPING CONTENTS
In the Box
Description (QTY)
B1. Beast5 handheld wet/dry tile saw (1)
B2. 5-inch blade (1)
B3. Blade wrench (1)
B4. T-wrench (1)
NOTE:
B5.
Blade Fence
B6. ¼-inch hose with standard hose
connection (1)
B7. 20mm to 5/8-inch bore adapter (1)
In the Hardware Bag
H1. M6 Wing screws (2)
H2. Wear-plate wedge clips (2)
7
