Instruction Manual |
7
Press
Short/Prog
once, and
change
ON
to
OFF
.
Then press both
Speed
and
Speed
at the same
time to save the setting,
and the keyboard beep
will be disabled. If you
want to exit during set
up, press
Start/Stop
and the setting will be
ineffective.
TEMP
TIME
TIME
TEMP
TIME
TEMP
TIME
TEMP
Press both
Speed
and
Speed
at the same time,
and the display will show
BEEP
.
Press
Speed
and
Speed
at the same time
to save the setting, and
buzz will be disabled upon
a failure occurrence or
ending. The display will
then show the keyboard
beep status. If the display
shows
ON K_S
, press
Short/Prog
once, and
change
ON
to
OFF
.
TEMP
TIME
TIME
TEMP
TIME
TEMP
TIME
TEMP
TEMP
TIME
TIME
TEMP
TIME
TEMP
TIME
TEMP
TEMP
TIME
TIME
TEMP
TIME
TEMP
TIME
TEMP
Press both
Temp
and
Temp
at the same time
to start the calibration. The
display will show 40.0 and
the temperature of the
instrument will automatically
increase to 40°C. Once the
temperature is kept constant,
timing will start.
30 minutes later, press
Short/Prog
one time, and the
display will show the blink
of
TEMP
. At this time, the
display will show the actual
temperature reading of the
thermometer (for example,
if the thermometer reads
40.5°C, you can adjust
the temperature display
to 40.5°C by pressing the
temperature button). Next,
press
Short/Prog
one time,
and the display will show
100.0°C. Following the
same instruction, when
the temperature of the
instrument increases to
100°C, wait for 30 minutes,
input the calibrated value, and
press
Short/Prog
to save it.
When the calibration
of 40°C is done, press
Start/Stop
to exit. At
this time the calibration
of 40°C is ineffective.
When the calibration
is done once at both
40°C and 100°C, check
for the discrepancy
between the two
calibration points and
the actual temperature
points. It should be
within 0.5°C. If it’s more
than 0.5°C, follow the
above instruction and
recalibrate until the
request is met.
TEMP
TIME
TIME
TEMP
TIME
SPEED
TEMP
TIME
SPEED
TEMP
TIME
SPEED
TEMP
TEMP
TIME
TIME
TEMP
TIME
SPEED
TEMP
TIME
SPEED
TEMP
TEMP
TIME
TIME
TEMP
TIME
SPEED
TEMP
TIME
SPEED
TEMP
Temp
Time
TEMP
TIME
TIME
TEMP
TEMP
TIME
TIME
TEMP
TIME
SPEED
TEMP
TIME
SPEED
TEMP
TIME
SPEED
TEMP
TEMP
TIME
TIME
TEMP
TIME
SPEED
TEMP
TIME
SPEED
TEMP
TIME
SPEED
TEMP
TEMP
TIME
TIME
TEMP
TEMP
TIME
TIME
TEMP
TIME
SPEED
TEMP
TIME
SPEED
TEMP
ME
SPEED
TEMP
TEMP
TIME
TIME
TEMP
TIME
TEMP
TIME
TEMP
TEMP
TIME
TIME
TEMP
TIME
SPEED
TEMP
TIME
SPEED
TEMP
TIME
SPEED
TEMP
TEMP
TIME
TIME
TEMP
TIME
SPEED
TEMP
TIME
SPEED
TEMP
TEMP
TIME
TIME
TEMP
TIME
SPEED
TEMP
TIME
SPEED
TEMP
Temp
Time
TEMP
TIME
TIME
TEMP
TEMP
TIME
TIME
TEMP
TIME
SPEED
TEMP
TIME
SPEED
TEMP
TIME
SPEED
TEMP
TEMP
TIME
TIME
TEMP
TIME
SPEED
TEMP
TIME
SPEED
TEMP
TIME
SPEED
TEMP
TEMP
TIME
TIME
TEMP
TEMP
TIME
TIME
TEMP
TIME
SPEED
TEMP
TIME
SPEED
TEMP
ME
SPEED
TEMP
TEMP
TIME
TIME
TEMP
TIME
TEMP
TIME
TEMP
TEMP
TIME
TIME
TEMP
TIME
SPEED
TEMP
TIME
SPEED
TEMP
TIME
SPEED
TEMP
TEMP
TIME
TIME
TEMP
TIME
SPEED
TEMP
TIME
SPEED
TEMP
TEMP
TIME
TIME
TEMP
TIME
SPEED
TEMP
TIME
SPEED
TEMP
Temp
Time
TEMP
TIME
TIME
TEMP
TEMP
TIME
TIME
TEMP
TIME
SPEED
TEMP
TIME
SPEED
TEMP
TIME
SPEED
TEMP
TEMP
TIME
TIME
TEMP
TIME
SPEED
TEMP
TIME
SPEED
TEMP
TIME
SPEED
TEMP
TEMP
TIME
TIME
TEMP
TEMP
TIME
TIME
TEMP
TIME
SPEED
TEMP
TIME
SPEED
TEMP
ME
SPEED
TEMP
TEMP
TIME
TIME
TEMP
TIME
TEMP
TIME
TEMP
7.5 Buzzer set up
Upon a failure occurrence or ending, the instrument will buzz. You may disable it if you do not need this function. However, the
default setting is to have it on.
This instrument has a keyboard beep. Once the button is pressed, it will beep once. You may disable it if you do not need this
function. However, the default setting is to have it on.