Labconco CentriVap 7812010 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 47

Labconco CentriVap 7812010 Скачать руководство пользователя страница 31

Chapter 6: Accessories for Your CentriVap Mobile System

Product Service 1-800-522-7658

27

7772700

Vacuum Pump Oil 1 Liter – A mineral oil with low vapor pressure. For
vacuum pumps 7439000, 7439200, 7769600 and 7769800

7438700

Vacuum Pump – Two stage direct drive pump, 108 liters/minute. 115 VAC
50/60 Hz, single phase. Includes Pump Exhaust Filter. (Catalog #7670400)

7438800

Vacuum Pump - Two stage direct drive pump, 108 liters/minute. 230 VAC
50/60 Hz, single phase. Includes Pump Exhaust Filter. (Catalog #7670400)

7769600

Vacuum Pump, Chemical Resistant - Two stage direct drive pump, 173
liters/minute. 115 VAC 50/60 Hz, single phase. Includes Pump Exhaust
Filter. (Catalog #7670400)

7769800

Vacuum Pump, Chemical Resistant - Two stage direct drive pump, 173
liters/minute. 230 VAC 50/60 Hz, single phase. Includes Pump Exhaust
Filter. (Catalog #7670400)

7439000

Vacuum Pump - Two stage direct drive pump, 173 liters/minute. 115 VAC
50/60 Hz, single phase 5.8 amps. Includes Pump Exhaust Filter. (Catalog
#7670400)

7439200

Vacuum Pump - Two stage direct drive pump, 173 liters/minute. 230 vac
50/60 Hz, single phase 2.9 amps. Includes pump exhaust filter. (Catalog
#7670400)

Installing a Vacuum Gauge

A user-supplied vacuum gauge may be attached to the CentriVap to monitor the
vacuum level. Attach the vacuum gauge to the barb end of the Quick Disconnect
Coupling fitting that was supplied with the CentriVap using a length of suitable
rubber hose. The Quick Disconnect Coupling fitting can then be pushed into the
mating connector on the rear of the CentriVap Mobile System. The Quick
Disconnect Coupling fitting can be removed from the mating connector by
pressing on the tab on the connector and then pulling out the Quick Disconnect
Coupling fitting. Always remove the Quick Disconnect Coupling from the
CentriVap when a vacuum gauge is not attached to it.

USER SUPPLIED
VACUUM TUBING

«
...
29
30
31
32
33
...
»

Содержание CentriVap 7812010
















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды