manualshive.com logo in svg

Labconco CentriVap 7812010, Руководство пользователя

Поделиться
Скачать
Labconco CentriVap 7812010 Скачать руководство пользователя страница 11

Chapter 3: Getting Started 

 

Product Service 1-800-522-7658 

7 

Unpacking Your CentriVap 

Carefully unpack your CentriVap and inspect it for damage that may have 
occurred in transit.  If your CentriVap is damaged, notify the delivery carrier 
immediately and retain the entire shipment intact for inspection by the carrier. 
 
The United States Interstate Commerce Commission rules require that claims be 
filed with the delivery carrier within fifteen (15) days of delivery. 
 

NOTE:  Do not return goods without the prior authorization of Labconco. 
Unauthorized returns will not be accepted.  If your CentriVap was damaged 
in transit, you must file a claim directly with the freight carrier.  Labconco 
Corporation and its dealers are not responsible for shipping damage. 

Do not discard the carton or packing material for your CentriVap until you have 
checked all of the components and installed and tested the CentriVap. 

CentriVap Components 

As previously mentioned, the CentriVap System is available in 115V or 230V.  
Locate the model of CentriVap you received in the following table.  Verify that 
the components listed are present and undamaged. 
 

Concentrator 

Catalog # 

Product Description 

7812010 

CentriVap Mobile System – 115V/60Hz 

7812011 

CentriVap Mobile System – 230V/50Hz 

7812012 

CentriVap Mobile System – 230V/60Hz 

7812013 

CentriVap Mobile System w/Heat Boost– 115V/60Hz 

7812014 

CentriVap Mobile System w/Heat Boost – 230V/50Hz  

7812015 

CentriVap Mobile System w/Heat Boost – 230V/60Hz 

Plus the Following: 
Part # 

Component Description 

7396603 

User’s Manual 

1336400 
 
1338000 

Power Cord – 115V 
or 
Power Cord – 230V 

1488800 

Clamp 

7397601 

Coupling Insert 

7455100 

Rotor (12-13 mm) 

7815200 

Cartridge, Solvent Trap 

 
If you do not receive one or more of the components listed for your CentriVap, or 
if any of the components are damaged, contact Labconco Corporation 
immediately for further instructions. 

Содержание CentriVap 7812010
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды