Lab.gruppen iP Series IP 450 Скачать руководство пользователя страница 8

 

Reverse operation of Channel B. 

RKPKP= q~åÇÉã=ãçÇÉ=

In tandem mode both channels' inputs are linked and receive the same signal. The tandem mode is 
active if the Link switches are in position "On". Both level attenuators are active, allowing you to set 
different levels for each channel. Note that only the inputs are connected in parallel. This is NOT a 
parallel output mode. 

Never connect either output terminal to ground or in parallel. 

You can use the remaining input connectors to carry signal to other amps. This is called “Daisy-
chaining”. 

NOTE: Always turn off the Link switch when using the amplifier for Bi-amping. 

RKPKQ= _êáÇÖÉ=ãçåç=ãçÇÉ=

 

Bridge mono mode is used to deliver both channels' power to a 
single load. The nominal impedance of the load must be more 
than 3 ohms. Set the Link switches to the “On” position and use 
one of the input connectors. You can use the remaining input 
connectors to carry signal to other amps. Both level attenuators 
must be at the same position. We recommend that you put them 
in the 0dB (full) position. 
Connect the speaker as shown. Always use Channel A’s output 
connector. 

RKPKR= _êáÇÖÉ=ãçåç=ãçÇÉ=ÑÉ~íìêÉë=

Bridged mono mode combines the power of both channels into 
one speaker. This results in twice the voltage swing, four times 
the peak power and just less than three times the full power of a 
single channel. 
 

One way to understand the load and p

 

ower from the amplifier’s perspective in bridged mode is that it is

zero voltage at the center of the voice-coil winding. This is because the coil is driven with positive 
voltage at one pole and an equivalent negative voltage at the other pole. So, if an 8 ohms load is 
connected in bridged mode, one channel shares one 4 ohms part of the load, and the other channel 
shares the other 4 ohms part. The power into 4 ohms from an iP 450 is 160 W. So, the total bridged 
power into the 8 ohms load will be 2 x 160 = 320 W. 
 

i~ÄKÖêìééÉå== =

=

=

=

=

========================

T

 

rëÉê=j~åì~ä===ám=QRM======sÉêëáçå=MKP========OMMPJMOJOR=

Содержание iP Series IP 450


















Отзывы: