background image

16 

 

Appendix C: 

Manufacturer’s Warranty

 

 
All  La Marche Manufacturing  Co. equipment has been thoroughly tested  and  found  to be in  proper  operating 

condition  upon  shipment  from  the  factory,  and  is  warranted  to  be  free  from  any  defect  in  workmanship  and 
material that may develop within two years from date of purchase.  
 

Any  part  or  parts  of  the  equipment  (except  fuses,  DC  connectors  and  other  wear-related  items)  that  prove 
defective within a two (2) year period shall be replaced without charge providing such defect, in our opinion, is 

due  to  faulty  material  or  workmanship  and  not  caused  by  tampering,  abuse,  misapplication  or  improper 
installation.  
 

Should a piece of equipment require major component replacement or repair during the first year of the warranty 
period, this can be handled in one of two ways: 

 
1. The equipment can be returned to the La Marche factory to have the  inspections, parts replacements and 

testing performed by factory personnel. Should it be necessary to return a piece of equipment or parts to the 
factory, the customer or sales representative must obtain authorization from the factory. If upon inspection at 
the factory, the defect was due to faulty material or workmanship, all repairs  will be made at no cost to the 

customer during the first year. Transportation charges or duties shall be borne by purchaser. 
2. If the purchaser elects not to return the equipment to the factory and wishes a factory service representative 

to make adjustments and/or repairs at the equipment location, La Marche's travel and field service labor rates 
will apply. A purchase order to cover the labor and transportation cost is required prior to the deployment of the 
service representative. 

 
In accepting delivery of the equipment, the purchaser assumes full responsibility for proper installation, installation 

adjustments  and  service  arrangements.  Should  minor  adjustments  be  required,  the  local  La  Marche  sales 
representative should be contacted to provide this service only. 

 
All sales are final. Only standard La Marche units will be considered for return. A 25% restocking fee is charged 
when return is factory authorized. Special units are not returnable. 

 
In no event shall La Marche Manufacturing Co. have any liability for consequential damages, or loss, damage or 

expense directly or indirectly arising from the use of the products, or any inability to use them either separately 
or in combination with other equipment or materials, or from any other cause. In addition, any alterations of 
equipment made by anyone other than La Marche Manufacturing Co. renders this warranty null and void. 

 
La  Marche  Manufacturing  Co.  reserves  the  right  to  make  revisions  in  current  production  of  equipment,  and 

assumes no obligation to incorporate these revisions in earlier models. 
 

The failure of La Marche Manufacturing Co. to object to provisions contained in customer's' purchase orders or 
other communications shall not be deemed a waiver of the terms or conditions hereof, nor acceptance of such 
provisions. 

 
The above warranty is exclusive, supersedes and is in lieu of all other warranties, expressed or implied, including 

any implied warranty of merchantability or fitness. No person, agent or dealer is authorized to give any warranties 
on behalf of the Manufacturer, nor to assume for the Manufacturer any other liability in connection with any of 
its products unless made in writing and signed by an official of the manufacturer. 

 
 

 
 

 

Содержание LMES Pro






















Отзывы: