30
POSITIONING THE TEMPERATURE SENSOR
The Sensor is supplied with a holder that may be attached to a wall with the two
screws supplied. The Sensor can also be position on a flat surface by securing
the stand to the bottom to the Sensor.
To wall mount:
1.
Secure the bracket onto a desired wall using the screws and plastic anchors.
2.
Clip the remote temperature sensor onto the bracket.
31
Note:
Before permanently fixing the sensor wall base, place all units in the desired locations to check that the
outdoor temperature reading is receivable. In event that the signal is not received, relocate the sensors or
move them slightly as this may help the signal reception.
CARE AND MAINTENANCE:
x
Extreme temperatures, vibration and shock should be avoided as these may cause damage to the
unit and give inaccurate forecasts and readings.
x
Precautions shall be taken when handling the batteries. Injuries, burns, or property damage may
be resulted if the batteries are in contact with conducting materials, heat, corrosive materials or
explosives. The batteries shall be taken out from the unit before the product is to be stored for a
long period of time.
x
Immediately remove all low powered batteries to avoid leakage and damage. Replace only with
new batteries of the recommended type.
x
When cleaning the display and casings, use a soft damp cloth only. Do not use solvents or
scouring agents as they may mark the LCD and casings.
x
Do not submerge the unit in water. Furthermore, fix all parts in place where the units are
adequately protected against moisture and rain.
32
x
Special care shall be taken when handling a damaged LCD display. The liquid crystals can be
harmful to user's health.
x
Do not make any repair attempts to the unit. Return them to their original point of purchase for
repair by a qualified engineer. Opening and tampering with the unit may invalidate their guarantee.
x
Never touch the exposed electronic circuit of the device as there is a danger of electric shock
should it become exposed.
x
Do not expose the units to extreme and sudden temperature changes, this may lead to rapid
changes in forecasts and readings and thereby reduce their accuracy.
SPECIFICATIONS:
Temperature measuring range:
Indoor
:
14.1°F to +139.8°F with 0.2°F resolution (-9.9ºC to +59.9ºC with 0.1ºC resolution);
“
OF.L
”
displayed if outside this range
Outdoor
:
-39.8°F to +139.8°F with 0.2°F resolution (-39.9ºC to +59.9ºC with 0.1ºC resolution);
“OF.L”
displayed if outside this range
Indoor relative humidity measuring range :
20% to 95% with 1% resolution (displays
“
- -
”
when the
measured humidity is outside the range or when the
indoor temperature reading is “OF.L”
)
33
Indoor temperature checking interval : every 16 seconds
Indoor humidity checking interval
: every 64 seconds
Outdoor data reception
: every 4 seconds
Power supply:
Weather station
: 2 x AA, IEC, LR6, 1.5V
Temperature sensor
:
2 x AA, IEC, LR6, 1.5V
Battery life cycle (Alkaline batteries recommended)
Weather station
:
Approximately 24 months
Temperature sensor
:
Approximately 24 months
Dimensions (L x W x H)
Weather station
:
3.18" x 1.22" x 5.64" (80.8 x 30.9 x 143.2 mm)
Temperature sensor :
1.50" x 0.83" x 5.05" (38.2 x 21.2 x 128.3 mm)
34
WARRANTY INFORMATION
La Crosse Technology, Ltd provides a 1-year limited warranty on this product against manufacturing
defects in materials and workmanship.
This limited warranty begins on the original date of purchase, is valid only on products purchased and
used in North America and only to the original purchaser of this product. To receive warranty service, the
purchaser must contact La Crosse Technology, Ltd for problem determination and service procedures.
Warranty service can only be performed by a La Crosse Technology, Ltd authorized service center. The
original dated bill of sale must be presented upon request as proof of purchase to La Crosse Technology,
Ltd or La Crosse Technology, Ltd’s authorized service center.
La Crosse Technology, Ltd will repair or replace this product, at our option and at no charge as stipulated
herein, with new or reconditioned parts or products if found to be defective during the limited warranty
period specified above. All replaced parts and products become the property of La Crosse Technology,
Ltd and must be returned to La Crosse Technology, Ltd.
Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever
is longer. La Crosse Technology, Ltd will pay all expenses for labor and materials for all repairs covered
35
by this warranty. If necessary repairs are not covered by this warranty, or if a product is examined which
is not in need or repair, you will be charged for the repairs or examination.
The owner must pay any shipping charges incurred in getting your La Crosse Technology, Ltd product to
a La Crosse Technology, Ltd authorized service center.
Your La Crosse Technology, Ltd warranty covers all defects in material and workmanship with the
following specified exceptions: (1) damage caused by accident, unreasonable use or neglect (including
the lack of reasonable and necessary maintenance); (2) damage occurring during shipment (claims must
be presented to the carrier); (3) damage to, or deterioration of, any accessory or decorative surface; (4)
damage resulting from failure to follow instructions contained in your owner’s manual; (5) damage
resulting from the performance of repairs or alterations by someone other than an authorized La Crosse
Technology, Ltd authorized service center; (6) units used for other than home use (7) applications and
uses that this product was not intended or (8) the products inability to receive a signal due to any source
of interference.
This warranty covers only actual defects within the product itself, and does not cover the cost of
installation or removal from a fixed installation, normal set-up or adjustments, claims based on
