background image

DETAILED SET-UP GUIDE 
 
I) BATTERY 

INSTALLATION 

 
Note:

 To avoid start-up problems make sure that the batteries do not spring free. 

 

 

5

A)  REMOTE TEMPERATURE TRANSMITTER 

 

1)  Remove the battery cover.  Place your thumb over 

the two air-vent slots on the face of the remote 
temperature sensor, push down gently, and slide 
battery cover down and off.

 

Battery 
Cover 

2)  Observing the correct polarity, install 2 AA batteries.  

The batteries will fit tightly (to avoid start-up 
problems make sure that they do not spring free 
during installation).

 

3)  Replace the battery cover.

 

 

 

B) TEMPERATURE CLOCK

 

 

1)  Remove the battery cover, 

located on the backside of the 
temperature clock and directly 
below the function buttons.

 

2)  Observe the correct polarity, 

and install 2 AA batteries.

 

3) Replace the battery cover. 

 

Note:

 After the batteries have been installed a tone will sound, and all the LCD’s 

(Liquid Crystal Display) will briefly light up.  The indoor temperature, the date as 
“1/ 1”, the weekday as “MON”, 
and the remote temperature will 
be displayed (within three 
minutes).  Also, the time will 
appear as “-:--” for 
approximately 1 minute.  The 
WWVB search is automatically 
initiated, and a tower icon 
appears and flashes with the time colon (no tower icon will appear if the WWVB is 
too weak to be detected, and the time display will remain on “-:--”). While the 
WWVB search is being conducted various numbers will appear in the time display. 
Within 10 minutes the temperature clock will either display the WWVB time, or 
discontinue the search if the time is not found. If the search is cancelled “-:--” will 
appear in the time LCD.  The temperature clock will conduct a WWVB search every 
hour until the first signal is found.  Once the WWVB time is found, a search is 
automatically conducted nightly at midnight. If the signal is found at midnight, the 
tower icon will remain, if not, another search will take place every hour (until 6:00 

Outdoor temperature 

Dat

WWVB 

Alarm 

Radio reception 

Indoor temperature or 
seconds display 

Weekday or 
seconds display 

Battery Compartment 

Battery Cover 

Содержание WS-8011UM-TWC



















Отзывы: