L-Acoustics X12 Скачать руководство пользователя страница 73

Страница: 73 / 100

Connection to LA amplied controllers

Connection to LA amplied controllers

Enclosure drive capacity per amplied controller

Make sure the total number of connected enclosures does not exceed the maximum number of enclosures per controller

(refer to the footnotes).

Refer to the

Amplication reference

technical bulletin for the latest information on compatibility with amplied

controllers and cabling schemes for all enclosure types.

LA4X

LA8

LA12X

per output

/ total

per output

/ total

per output

/ total

X12

1 / 4

2 / 8

3 / 12

Cabling schemes for X12

Refer to the cabling schemes to connect the enclosures to different types of output connectors.

One-channel speakON output

1+/1-

Two-channel speakON output

SP-Y1

CC4FP

CH(1)

CH(2)

1+/1-

2+/2-

Four-channel CA-COM output

B-

SPK1

SPK2

SPK3

SPK4

For passive loudspeakers, the value corresponds to the number of enclosures in parallel on the output. For active

loudspeakers, the value corresponds to the number of sections in parallel on the output.

X12 owner's manual (EN) version 1.0

Содержание X12





































































































Результаты поиска

Содержание X12

Отзывы:

Похожие инструкции для X12

Бренды по названию

Популярные бренды

L-Acoustics X12, Руководство пользователя

Результаты поиска

Содержание X12

Отзывы:

Похожие инструкции для X12

Бренды по названию

Популярные бренды