L-Acoustics SB18 IIi Скачать руководство пользователя страница 49

Страница: 49 / 66

Corrective maintenance

Corrective maintenance

Introduction

This section contains the following maintenance procedures:

SB18 IIi

•

Grill

(p.51)

•

LF speaker

(p.52)

For advanced maintenance, contact your L-Acoustics representative.

Tools

Before performing maintenance on this product, make sure all the tools listed are available. References are given for

FACOM

products in this table. Other manufacturers can be used.

name

reference

distributor

Set of 6-point 1/4" sockets *

RL.NANO1 / R.360NANO

FACOM

Torque screwdriver (2 - 10 N.m) *

A.404

FACOM

* included in the L-Acoustics Maintenance Toolcase.

Maintenance Toolcase

The Maintenance Toolcase is a carry-on suitcase that includes all the tools required to perform maintenance on L-

Acoustics products. This toolcase is aimed at Certied Providers.
The Maintenance Toolcase uses a Peli

™

1510 Protector case that features three pre-cut layers of foam to safely t the

tools. The Maintenance Toolcase includes tools manufactured by FACOM

, Fluke

, Tohnichi, ABUS and Würth.

All third-party trademarks, registered trademarks, or product names are the property of their respective owners.

SB18 IIi owner's manual (EN) version 1.0

Содержание SB18 IIi



































































Результаты поиска

Содержание SB18 IIi

Отзывы:

Бренды по названию

Популярные бренды

L-Acoustics SB18 IIi, Руководство пользователя

Результаты поиска

Содержание SB18 IIi

Отзывы:

Бренды по названию

Популярные бренды