manualshive.com logo in svg

L-Acoustics SB18 IIi, Руководство пользователя

Поделиться
Скачать
L-Acoustics SB18 IIi Скачать руководство пользователя страница 24

Loudspeaker congurations

SB18 IIi in cardioid conguration

Deployed in a cardioid conguration, an SB18 IIi system produces a rear SPL rejection. The deployment consists of

an array of four SB18 IIi with one element turned towards the rear (reversed). Refer to the 

Cardioid Conguration

technical bulletin for more information.
The [SB18_60_C] / [SB18_60_Cx], and [SB18_100_C] / [SB18_100_Cx] factory presets provide the subwoofer system

with an upper frequency limit at 60 Hz and 100 Hz respectively in order to optimize the acoustic coupling with a main

full-range system.
The SB18 IIi subwoofer is driven by the  LA2Xi / LA4X / LA8 / LA12X  amplied controllers

Reduced maximum SPL or drive capacity with LA2Xi: refer to the 

LA2Xi owner's manual

.

Preset

[SB18_60_C] / [SB18_60_Cx]

[SB18_100_C] / [SB18_100_Cx]

Low frequency limit (-10 dB)

32 Hz

Delay values

When combining a line source with subwoofers, delays may have to be added to the presets.
Refer to the Preset Guide to obtain the pre-alignment delay values.

24 

 SB18 IIi owner's manual (EN) version 1.0

Содержание SB18 IIi



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды