L-Acoustics K Series Скачать руководство пользователя

Страница: 42 / 120

Inspection and preventive maintenance

Rigging part inspection

About this task

For critical rigging parts, use the

Inspection references

(p.50) for comparison and specic manipulations.

Prerequisite

Perform the inspection in a well-lit environment.

Procedure

Check that the rigging part is present.

If applicable, disassemble the rigging part from the enclosure or the rigging accessory.
Check that the tethers are intact and safely secured.

Inspect the part from every side.
Compare with the

reference pictures

Check for:

• corrosion
• wear and cracks
• bends and dents
• holes
• missing safety cues
• missing identication labels
• missing or loose fasteners

Replacing screws

If a screw is loose, remove and replace it.
Always use the new screws provided in the repair kit.
If no new screw is available, add blue threadlocker before reusing the screw.
Do not apply more than the indicated torque.

Check the

geometry

of the part to identify critical deformations.

Place the rigging part on a at surface or hold a level against it.

Check the

moving parts

Make sure that the mechanism engages correctly.

What to do next

If a problem is detected, perform the authorized maintenance operations or contact your L-Acoustics representative.

Mechanical system overview

Critical parts of the lifting chains are highlighted.

The

indicates a visual inspection. The

indicates a functional check.

Perform the

Rigging part inspection

(p.42) on critical parts.

For each part, refer to the

Inspection references

(p.50).

Replacing screws

K3 owner's manual (EN) version 1.0

Содержание K Series

























































































































Результаты поиска

Содержание K Series

Отзывы:

Похожие инструкции для K Series

Бренды по названию

Популярные бренды

L-Acoustics K Series, Руководство пользователя

Результаты поиска

Содержание K Series

Отзывы:

Похожие инструкции для K Series

Бренды по названию

Популярные бренды