background image

12

1

飛行場所は慎重に選ぼう!

P‑51D ムスタング M24 飛行手順の注意 / 

P-51D Mustang M24 FLIGHT MANUAL  

●気軽に飛ばせ操縦もやさしい電動プレーン。でも空を飛び回るものだから安全確認は重要です。
 この『飛行手順の注意』をよく読んで、安全な飛行方法について十分理解しておきましょう。
●R/Cプレーンが初めてという方の単独飛行はできません。必ずベテランの指導を受けてください。

●こんな場所での飛行は絶対に禁止です!

●理想的な飛行場所は…

2

フライト条件

●初飛行は風速2〜3mの弱風が基本!

人家やビル、子供の遊び場や
公園、交通量の多い道路、鉄
道、飛行場、高圧線、鉄塔な
どのそばは飛行禁止。また飛
行範囲に人、特に子供が入っ
てこないように注意する。

飛行場所は左図のような四方が
広く人がいない場所が理想的で
す。(模型飛行機専用の飛行場
を使用する場合は、必ず管理者
の許可をとってください。)

強風での飛行や、横風・追い風で
の離着陸は禁止。

強風

2~3m

弱風

弱風

強風

強風

●Electric plane with gentle flying characteristics. Safety checks on flying models are essential.
 Please read this "Flight Manual" carefully to understand how to operate this model safely.
●First time fliers of R/C planes should seek the supervision of experienced model plane fliers.

/ Choose Location Carefully

 / Flight Conditions

Do NOT operate model near these areas

First flight should be in light wind speeds up to 2 - 3m

Do NOT use near: houses or 
buildings; children's play 
areas; road traffic; 
railways; airports; 
overhead powerlines and 
pylons. Make sure no 
people, especially 

The ideal location for 
flying has wide‑open space 
in four directions with no 
people. (If using a model 
airfield, be sure to contact 
the airfield's administrator 
for permission).

Do NOT try to land or take‑off 
with strong cross or tail 
winds.

Strong

Wind

2~3m

Light Wind

Light

Wind

Wind

Strong

Wind

Strong

Содержание 10231



















Отзывы: