manualshive.com logo in svg

Kyoritsu Electrical Instruments Works 5000, Инструкция по эксплуатации

Поделиться
Скачать
Kyoritsu Electrical Instruments Works 5000 Скачать руководство пользователя страница 10

― 8 ―

5. Before starting measurement & record

5-1 Power on/off the instrument

Instrument  can  be  powered  on  by  pressing  "MENU/ENTER"  button

1sec. or more

when it is in OFF status.

When all indications are displayed on the LCD, release the button.
To power off the instrument, press "MENU/ENTER" button 

1sec. or 

more

while  making  normal  measurement.  (Instrument  cannot  be

powered  off  while  recording  data.  Stop  the  recording,  and  power  off
the  instrument.)  Then  "OFF"  will  be  displayed  on  the  LCD  and
instrument is powered off when releasing then button.

5-2 Battery voltage check

Power  on  the  instrument.  When  the  battery  mark  displayed  on  the
LCD  is  last  1level  (

)  or  no  indication  on  the  LCD,  replace

batteries.  When  no  indications  displayed  on  the  LCD,  battery  is
exhausted. Replace it new one.

5-3 Auto-power off

When turning on Auto-power off function in Menu: "Setting2 (SEt.2)",
automatically  switches  the  instrument  off  approx.  in  3  minutes  after
the last operation of switch.
While  recording,  instrument  will  not  be  switched  off  but  indicate
battery mark and recording mark, etc instead of the measured value.
Measured values can be displayed again by operating any button.
When  turning  off  Auto-power  off  function,  instrument  will  not  be
switched off automatically. Be sure to switch off the instrument after
use.
(Please  refer  to  the  instruction  manual,  page  31  "9.Menu  operation"
for further details.)

5-4 Sensor connection

This  instrument,  Leak  logger,  can  perform  measurement  and  record
by  using  sensors  via  3ch.  Pay  attention  to  the  direction  of  the
connector of sensor cable and firmly connected it. Press "CH" button
on the instrument and display the channel in use. 
When the sensor is not connected correctly, "nc" is displayed on the
LCD.  If  this  message  is  displayed,  confirm  that  no  dust  on  the
connector terminal and connect the sensor again.

Содержание 5000













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды