Kyocera PF-410 Скачать руководство пользователя страница 39

Страница: 39 / 55

3HW

1-5-8

(5) Adjusting the center line of image printing

Make the following adjustment if there is a regular error between the center lines of the copy image and original when
paper is fed from the drawer.

Caution

Check the copy image after the adjustment. If the image is still incorrect, perform the above adjustments in maintenance
mode.

Procedure

Figure 1-5-9

U072

(See the service manual

of the copier.)

U067

(See the service manual

of the copier.)

U034

Yes

Start

Enter maintenance mode.

Enter “034” using the numeric keys.

Press the start key.

Press the interrupt key.

Press the start key to output a test
pattern.

Is the image correct?

Press the start key.

The new setting is stored.

Press the stop/clear key to exit

maintenance mode.

End

Press the image mode selection key
to light the photo and text indicators.

For output example 1, decrease
the value using the zoom (–) key.
For output example 2, increase
the value using the zoom (+) key.

Setting range: –8.0 – +10.0
Initial setting: 0.0
Changing the value by 1 moves the
center line by 1 mm.

Select the item to be adjusted

using the copy exposure

adjustment keys.

●

Image mode selection key

Photo and text indicators are on:
Center line adjustment

●

Copy exposure adjustment keys

Exp. 1 (lit): Drawer
Exp. 2 (lit): Bypass tray
Exp. 3 (lit): First paper feeder
Exp. 4 (lit): Second paper feeder
Exp. 5 (lit): Third paper feeder
Exp. 1 (flashing): Duplex copying (second face)

Photo
Text

Center line of printing

Correct image

Output

example 1

Output

example 2

Содержание PF-410
























































Результаты поиска

Содержание PF-410

Отзывы:

Похожие инструкции для PF-410

Бренды по названию

Популярные бренды

Kyocera PF-410, Руководство по обслуживанию

Результаты поиска

Содержание PF-410

Отзывы:

Похожие инструкции для PF-410

Бренды по названию

Популярные бренды