Kyocera PF-100 Скачать руководство пользователя страница 25

Страница: 25 / 44

3LF/3N2

1-3-5

(3) Self diagnostic codes

Code

Contents

Remarks

Causes

Check procedures/corrective measures

0420

Paper feeder communication error

Communication error between
printer’s control PWB and paper
feeder.

Improper installation
paper feeder.

Follow installation instruction carefully
again.

Defective harness
between paper feeder
interface connector and
control PWB (YC318),
or improper connector
insertion.

Reinsert the connector. Also check for con-
tinuity within the connector harness. If
none, remedy or replace the harness
(Refer to the service manual for the
printer).

Defective control PWB.

Replace the control PWB (Refer to the ser-
vice manual for the printer).

Defective harness
between PF main PWB
(YC5) and paper feeder
interface connector, or
improper connector
insertion.

Reinsert the connector. Also check for con-
tinuity within the connector harness. If
none, remedy or replace the harness (See
page P.1-4-6).

Defective PF mainPWB. Replace the PF main PWB (See page P.1-

4-6).

2610

PF paper feed motor error (Paper
feeder 1)

The PF paper feed motor of paper
feeder 1 ready input is not given for 2
s during the PF paper feed motor is
ON.

Defective harness
between PF paper feed
motor and PF main
PWB (YC4), or improper
connector insertion.

Reinsert the connector. Also check for con-
tinuity within the connector harness. If
none, remedy or replace the harness (See
page P.1-4-6).

Defective PF paper feed
motor drive
transmission system.

Check if the gears rotate smoothly. If not,
grease the bushings and gears. Check for
broken gears and replace if any.

Defective PF main
motor.

Replace the PF main motor.

Defective control PWB.

Replace the control PWB (Refer to the ser-
vice manual for the printer).

2620

PF paper feed motor error (Paper
feeder 2)

The PF paper feed motor of paper
feeder 2 ready input is not given for 2
s during the PF paper feed motor is
ON.

Defective harness
between PF paper feed
motor and PF main
PWB (YC4), or improper
connector insertion.

Reinsert the connector. Also check for con-
tinuity within the connector harness. If
none, remedy or replace the harness (See
page P.1-4-6).

Defective PF paper feed
motor drive transmis-
sion system.

Check if the gears rotate smoothly. If not,
grease the bushings and gears. Check for
broken gears and replace if any.

Defective PF main
motor.

Replace the PF main motor.

Defective control PWB.

Replace the control PWB (Refer to the ser-
vice manual for the printer).

Содержание PF-100













































Результаты поиска

Содержание PF-100

Отзывы:

Бренды по названию

Популярные бренды

Kyocera PF-100, Руководство по обслуживанию

Результаты поиска

Содержание PF-100

Отзывы:

Бренды по названию

Популярные бренды