background image

© 2018 Kymeta Corporation.

6

07 February 2018

KyWay™ Terminal Quick Start Guide

8 Connect the cables

Avoid confusing the Rx and Tx cables. Before installing the cables, apply colored tape to each end of the cable, or install

one cable at a time. The recommended convention is

RED

for the

Tx cable

and

BLUE

for the

Rx cable

.

1.

Connect the ODU interface cable 31-pin connector to the back of the ASM by carefully aligning the connector

keys on the inside bulk and on the inside of the outer ring. The connector should seat firmly without forcing it. You

may feel a slight click as the connector reaches the end of travel.

2.

Connect the ODU interface cable 12-pin Amphenol connector to the 12-pin receptacle on the BUC.

3.

Connect the Tx cable (

RED

) to the BUC (use the torque wrench).

4.

Connect the Rx cable (

BLUE

) to the ASM Rx OUT port (use the torque wrench).

5.

Connect the ODU interface cable 18-pin connector to the mTenna I/O.

6.

Connect the Rx cable (

BLUE

) to the modem primary Rx IN port (Rx 1) (finger-tighten).

Do not use the Rx 2 port.

7.

Connect the Tx cable (

RED

) to the Tx OUT of the modem (finger-tighten).

8.

Connect the Ethernet cable to the mTenna I/O and port 1 on the modem.

9.

(optional)

Connect the customer Ethernet cable to the modem (port 5-8 for DHCP).

10.

Connect one power cable to the mTenna I/O and another one to the modem.

Use cable ties to clean up loose cables.

Содержание KyWay U7 8W











Отзывы: