background image

KVH, TracVision, and the unique light-colored dome with dark contrasting baseplate are registered trademarks of KVH Industries, Inc. 
All other trademarks are property of their respective companies. The information in this document is subject to change without notice. 

No company shall be liable for errors contained herein. © 2008-2010 KVH Industries, Inc., All rights reserved. 

54-0438 Rev. C

1

These instructions explain how to install the TracVision R5SL/R4SL on an RV or motor coach. 
Complete instructions on how to use the system are provided in the 

User’s Guide

.

Installation Steps

Who Should Install the System?

To ensure a safe and effective installation, KVH recommends that a KVH-authorized technician 
install the TracVision R5SL/R4SL system. To find a technician near you, please visit 

www.kvh.com/wheretogetservice

.

 If you purchased the product and decide to install it 

yourself, please see the enclosed warranty statement for warranty implications.

Related Documentation

The following additional documents are provided with the TracVision R5SL/R4SL system:

Technical Support

If you need technical assistance, please contact KVH Technical Support:

Phone: +1 401 847-3327
E-mail: [email protected]

(Mon.-Fri., 9 am-6 pm ET; Sat. 9 am-2 pm ET)

1.

Inspect Parts and Get Tools ............ 3

2.

Plan the Installation.......................... 4

3.

Remove the Restraints ..................... 5

4.

Mount the Antenna .......................... 6

5.

Cut Out the Switchplate Hole......... 7

6.

Wire the Antenna ............................. 8

7.

Seal the Cable Access Hole.............. 9

8.

Wire the Receiver(s) ....................... 10

9.

Ground the System......................... 11

10.

Wire the Switchplate...................... 12

11.

Install Service Key(s)...................... 13

12.

Mount the Switchplate................... 14

13.

Set Up and Test the System........... 15

14.

Educate the Customer.................... 16

Document

Description

User’s Guide

Operation, setup, and troubleshooting information

Product Registration Form

Details on registering the product with KVH

Warranty Statement

Warranty terms and conditions

Contents List

List of every part supplied in the kit

TracVision

®

 

R5SL/R4SL Installation Guide

Содержание TracVision R4SL




















Отзывы: