KVH Industries TracPhone V11IP Скачать руководство пользователя | Manualshive

Страница: 9 / 55

background image

8

Follow these steps to prepare the ICM for
installation.

Connect the ICM Jumper Cables

Connect the two supplied jumper cables to the
rear panel of the ICM (see Figure 7).

a.

Connect the serial data cable from the “A1”

jack to the “A2” jack.

b.

Connect the straight-through Ethernet cable

from the “B1” jack to the “B2” jack.

Attach the Wi-Fi Antennas

Connect the two supplied Wi-Fi antennas to the
rear panel of the ICM (see Figure 7).

ICM

A2

A1

B2

B1

Wi-Fi Antenna (x2)

Figure 7: Jumper Cables Wiring and Wi-Fi Antennas

Prepare the ICM

4

«
...
7
8
9
10
11
...
»

Содержание TracPhone V11IP
























































Отзывы:

Нет отзывов

Похожие инструкции для TracPhone V11IP

Бренд: Hirschmann Страницы: 2

Бренд: Diamond Antenna Страницы: 2

Бренд: Opticum Red Страницы: 4

Бренд: Maco Antennas Страницы: 9

DB42 MonstIR PRO

Бренд: SteppIR Страницы: 7

Бренд: SteppIR Страницы: 80

SNIPE MOBIL CAMP

Бренд: SELFSAT Страницы: 48

Бренд: Televes Страницы: 24

Бренд: Sirio Antenne Страницы: 2

Бренд: Sirio Antenne Страницы: 4

Бренд: Vivax Страницы: 44

Бренд: Hughes Network Страницы: 86

Бренд: Globalstar Страницы: 57

Бренд: A.H. Systems Страницы: 10

Бренд: Jack Страницы: 4

Hi-Gain HAO15SIP

Бренд: Hawking Страницы: 2

Бренд: Triax Страницы: 2

Бренд: Triax Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды