Follow the steps below to turn on the system and
start using the MSN TV service.
1. Apply vehicle/vessel power.
2. Press the receiver’s front panel power switch.
The receiver’s #1 “Activity” light should be lit
green. If this light is off, check the short
Ethernet patch cable on the back of the receiver.
The receiver’s “Power” light should come on or
start flashing green. If this light is off, press the
MSN Power
button on the remote or keyboard.
3. Turn on your TV.
4. Wait about two minutes for the MSN TV service
to start up. During startup, the TV will show an
MSN TV bootup screen. Then
the screen will
go totally blank for 30 seconds
before the MSN
TV Welcome screen appears.
5. Now you need to create your MSN TV account.
Using the remote or keyboard, select
Continue
and follow the steps on the screen. You must
enter your MSN TV promotion code when
prompted. This promotion code, which you
received during activation, will personalize your
MSN TV service for your mobile environment
and ensure the correct software is loaded into
your system.
Refer to Section 3.1 of the
User’s Guide for
details.
1. Turn off the power switch on the TracNet 100
receiver’s front panel and power off your laptop.
2. Connect a straight (not crossover) Ethernet
cable from your computer to one of the
available RJ45 ports on the receiver (2, 3, or 4).
Do not disconnect the patch cable from port 1.
3. Turn on the TracNet 100 receiver, wait two
minutes, then turn on your computer.
4. Configure your computer’s LAN connection to
obtain IP/DNS server addresses automatically.
Refer to Section 4.1 of the
User’s Guide for details.
1. Turn off the power switch on the TracNet 100
receiver’s front panel and power off your laptop.
2. Make sure the WiFi antenna is connected.
3. Turn on the TracNet 100 receiver, wait two
minutes, then turn on your computer.
4. Enable your computer’s wireless card and
connect to the “KR1” wireless network.
Refer to Section 4.2 of the
User’s Guide for details.
To block intruders from “piggybacking” on your
connection, and optimize data speeds, establish
basic security settings on TracNet 100, even if you
are using MSN TV. Just run the router setup wizard,
which walks you through the process step-by-step.
From MSN TV Sign In Page
: Go to Settings>Choose
Connection Setting>Configure Router. Then select
IP address 192.168.0.1 and select Access Router.
From a PC
, enter http://192.168.0.1 in the browser.
When finished, turn the receiver off then back on.
Refer to Section 4.3 of the
User’s Guide for details.
Mount the receiver in a dry, well-ventilated area
away from heat sources or electrical devices that
generate RF noise (e.g., microwave, plasma TV, or
motor). Do not block the receiver’s vents. Ensure
both front/back panels are accessible to the user.
1. Attach the two mounting brackets to the
receiver’s side vents using #2-56 screws.
2. Secure the brackets to the mounting surface
using appropriate
1
⁄
4
" fasteners.
If you experience a problem with the TracNet 100
system, first check the following:
•
Check the signal strength bars on the MSN TV
screen. If you have no bars, you are outside the
coverage area of the nearest cell tower.
•
Check the batteries in the remote or keyboard.
•
Check the connections on the receiver rear panel.
•
If you are using a computer, check the
computer’s network connection (enabled?).
Refer to Section 5 of the
User’s Guide for details.
Getting Started with MSN TV
Power Switch
Power Light
#1 Activity Light
TracNet 100 Internet Receiver – Front Panel
C AU T I O N
Ethernet Ports
2
4
3
WiFi Antenna
Do Not
Remove!
1
TracNet 100 Internet Receiver
Computer Connections
MSN Power Button
Connecting a Computer – Wired
Mounting the Receiver
Protecting Your Network Connection
Bracket
#2-56
S
crew
s
x 3
1⁄4" Fa
s
te
n
er
s
x 4
(not supplied)
Connecting a Computer – Wireless
54-0352 Rev
. B
KVH Technical Support supports Windows 2000/XP only for wired computer
connections and supports Windows XP only for wireless computer connections.
Receiver Mounting
Troubleshooting
Technical Support
If you need help, please contact KVH Technical Support:
Tel: 866-399-8509
(Mon-Fri 9 a.m.-6 p.m., Sat. 9 a.m.-2 p.m. ET)
E-mail: [email protected]
