Kuzma XL DC Скачать руководство пользователя страница 11

 

11 

Raising    the  VTA  by  rotating  the    toothed  knob,  will  show  increased  height  above  this 
reference point in mm and lowering  it  will show minus numbers.  The precision achieved by 
this  is  0.01mm.    If  the  change  in  height  of  the  tonearm  comes  outside  this  range  of 
measurement,  the  brass  weight  can  be    repositioned.    The  measuring  device  will  not  be 
damaged by being  outside its  range.  Each rotation of the knob corresponds to 1mm change 
in VTA and it can  be moved while playing records. 

 
 

Use and adjustments: 

 
Operation  & speed selection

1. Press the power button at the front of the PS DC firmly.  After 10 sec the PS is ready.  The 
display  will  show  33(  or  45)  and  above  the  start  button  a  red  LED  will  be  shown.  You  can 
keep the PS DC switched on all the time. 
2.  On  pressing  the  start  button  the  red  LED  will  turn  green  and  the  platter  should  start 
rotating.  To stop the platter, simply press the start button again. The red LED will show and 
the platter will slowly stop rotating. 
3. Press the speed button and the selected speed will change from 33 to 45.  Press again and it 
will return to 33. 
4. Do not press and hold the start button before the mains switch is on( see Reset function). 
5. 78rpm- see below 
 

Fine speed adjustment: 

Observe on a strobe disc if the bars are stationary-  that is  the correct  speed.   If they are not 
(for example if the bars move in the same direction as platter rotation) then the speed is too 
high. Press the plus or minus buttons a few times until the bars are stationary (there are very 
small steps,  press several times).  On the display you will see a green dot in the right bottom 
corner  indicating  that  a  change  is  in  process.    Using  a  pointed  pen  or  toothpick,  press  the 
“store” button and the green dot will disappear.   
Resetting the PS causes  the speed change. After the PS is reset there  will be comparatively 
large steps towards plus or minus speed change**. When the “store” button is pressed  next  
the changes will be smaller until, finally the speed changes are barely visible.  
Check the speed independently for both speeds.  When using the strobe disc, be sure to use it 
properly.  Check  that  you  are  looking  at  the  correct  speed  and  are  using  the  correct  strobe 
light. 

 
Temporary options: 
 
78 rpm speed: 

While platter is not rotating ( press start/stop button), then press and hold + button for 7- 10 
seconds, then press speed button to  show 78. Then press start for platter rotation. Pressing the 
speed button will show  all three speeds. 
 
 

Clamp: (

Gently screw down the clamp on  top of the record) 

Put  a    washer  under  the  LP  (thin  for  thick  records  and  thick  for  thin  records)  and  start 
screwing  the clamp down.  Observe the outer edge of the LP.  To start with, this edge will be 
above the mat but  will slowly lower to  touch the mat.  With fingers hold  the LP so  that  it 
does not rotate.  If the clamp is further screwed, the outer edge will rise.  

Содержание XL DC














Отзывы: