background image

®

03

III. SPECIAL FEATURES :

VFD V & Hz readings.                                           

Record MAX / MIN readings.                               

Display Hold Function.

Display.

LOCK-Test mode for Insulation Resistance & 

   Earth Continuity Test.                         

BeepJack  audible & visible input warning.      

Remote Probe for insulation Resistance & 

   Earth Continuity Test.

  

  

Paper-White 

  

  

  

Dual Digital 

  

  

  

Backlight LCD Display

TM

CAUTION :

Disconnect  the  test  leads  from  the  test  points  before  changing 
functions. Always set the instrument to the highest range and work
downward for an unknown value when using manual ranging mode.

INTERNATIONAL ELECTRICAL SYMBOLS :

Caution !  Refer to the explanation in this Manual
Caution !  Risk of electric shock
Earth (Ground)
Double Insulation or Reinforced insulation
Fuse
AC--Alternating Current
DC--Direct Current

II. CENELEC DIRECTIVES :

The instruments conform to CENELEC Low-voltage directive 2006/
95/EC and Electromagnetic compatibility directive 2004/108/EC.

®

04

IV. GENERAL SPECIFICATIONS :

Display                             :

 3-5/6 digits 6,000 counts

Polarity                             :

 Automatic

Update Rate                     :

 5 per second nominal

61 Segments Bar graph  :

 40 per second max

Operating Temperature   :

 -1

0

ºC to 40ºC

Relative Humidity            :

 Maximum relative humidity 90% for

                                            temperature up to 28ºC decreasing
                                            linearly to 50% relative humidity at 40ºC

Pollution degree              :

 2

IP Rating                           :

 IP40

Storage Temperature      :

 -20ºC to 60ºC, < 80% R.H. 

                                            (with battery removed)

Altitude                             :

 Operating below 2000m

Temperature Coefficient :

 nominal 0.15 x (specified accuracy)/ºC 

                                            @(-10ºC ~ 18ºC or 28ºC ~ 40ºC), or 
                                            otherwise specified

Sensing                            :

 AC, True RMS

Low Battery                      :

 Approx. 4.6V

APO Timing                      :

 Idle for 20 minutes

APO Consumption          :

 50

m

A typical

Power Supply                  :

 Four Alkaline AA batteries (IEC LR6)

Power Consumption       :

 4.5mA typical except: 

+Hz

+Hz

                                            ACV  & VFD ACV : 7.0mA

Dimension                        :

 208(L) X 103(W) X 64.5(H) mm 

                                             with holster

Weight                              :

 635 gm with holster

Accessories                     :

 Test probe pair, Alligator clip pair, 

                                            BRP21S2-C Remote probe, Holster,  
                                            User manual, Bkp60 banana plug  
                                            K-type thermocouple.

Optional Accessories      :

 BKB32 banana plug to type-K socket 

                                            plug adaptor & Magnetic hanger.

Содержание KM 878





















Отзывы: