Kurzweil Mark Pro 2i Скачать руководство пользователя страница 2

 

 

IMPORTANT SAFETY & INSTALLATION INSTRUCTIONS 

INSTRUCTIONS PERTAINING TO THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS 

 
 

WARNING:   When    using    electric    products,    basic    precautions   
should 
always be followed, including the following: 

 

1.        Read all of the Safety and Installation Instructions and 

Explanation of Graphic Symbols before using the product. 

 

2.        Do not use this product near water—for example, near a 

bathtub, washbowl,  kitchen  sink,  in  a  wet  basement,  or  near  a 
swimming pool, or the like. 

 

3.        This    product    should    be    used    only    with    a    stand    or   

cart    that    is recommended by the manufacturer. 

 

4.        This product, either alone or in combination with an amplifier 

and speakers    or    headphones,    may    be    capable    of   
producing    sound levels that could cause permanent hearing loss. 
Do not operate for 
a  long  period  of  time  at  a  high  volume  level  or  at  a  level  that  is 
uncomfortable. If you experience any hearing loss or ringing in the 
ears, you should consult an audiologist. 

 

5.        The product should be located so that its location or position 

does not interfere with its proper ventilation. 

 

6.        The  product  should  be  located  away  from  heat  sources  such 

as radiators, heat registers, or other products that produce heat. 

 

7.        The product should be connected to a power supply only of the 

type described in the operating instructions or as marked on the 
product. 

 

8.        This product may be equipped with a polarized line plug (one 

blade wider than the other). This is a safety feature. If you are 
unable to insert the plug into the outlet, contact an electrician to 
replace your obsolete outlet. Do not defeat the safety purpose of 
the plug. 

9.        The power supply cord of the product should be unplugged from 
the 

outlet when left unused for a long period of time. When unplugging 
the power supply cord, do not pull on the cord, but grasp it by the 
plug. 

 

10.      Care should be taken so that objects do not fall and liquids are not 

spilled into the enclosure through openings. 

 

11.      The    product    should    be    serviced    by    qualified    service   

personnel when: 

 

A.        The power supply cord or the plug has been damaged; 

 

B.        Objects  have  fallen  onto,  or  liquid  has  been  spilled  into 

the product; 

 

C.        The product has been exposed to rain; 

 

D.        The   product   does   not    appear   to    be   operating   

normally   or exhibits a marked change in performance; 

 

E.        The product has been dropped, or the enclosure damaged. 

 

12.      Do not attempt to service the product beyond that described in 

the user     maintenance     instructions.    All     other     servicing     
should     be referred to qualified service personnel. 

 

13.      WARNING: Do   not   place   objects   on   the   product’s   power   

supply cord,  or  place  the  product  in  a  position  where  anyone 
could  trip over, walk on, or roll anything over cords of any type. 
Do not allow the    product    to    rest    on    or    be    installed    over   
cords    of    any    type. Improper   installations   of   this   type   
create   the   possibility   of   a   fire hazard and/or personal injury. 

RADIO AND TELEVISION INTERFERENCE 

 

WARNING: Changes or modifications  to  this  instrument not expressly 
approved    by   Young    Chang    could    void    your    authority    to   
operate    the instrument. 

 

IMPORTANT: When connecting this product to accessories and/or other 
equipment use only high quality shielded cables. 

 

NOTE: This instrument has been tested and  found to comply with the 
limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. 
These    limits    are    designed    to    provide    reasonable    protection   
against harmful    interference    when    the    instrument    is    used    in   
a    commercial environment. This   instrument   generates,   uses,   
and   can   radiate   radio frequency energy and, if not installed and 
used in accordance with the instruction       manual,       may       cause       
harmful       interference       to       radio communications.  Operation   of   
this   instrument   in   a   residential   area   is likely    to    cause   
harmful    interference,    in    which    case    the    user    will    be required 
to correct the interference at his or her own expense. 

 

Changes and modifications not expressly approved by the manufacturer 

 

or registrant of this instrument can void the user’s authority to operate 
this instrument under Federal Communications Commission rules. 

 

In order to maintain compliance with FCC regulations, shielded cables 
must      be      used      with      this      instrument.     Operation      with     
unapproved equipment or unshielded cables is likely to result in harmful 
interference to radio and television reception. 

 

NOTICE 

This    apparatus    does    not    exceed    the    Class    A    limits    for   
radio    noise emissions    from    digital    apparatus    set    out    in    the   
Radio    Interference Regulations of the Canadian Department of 
Communications. 

 

AVIS 

Le   present   appareil   numerique   n’emet   pas   de   bruits   
radioelectriques depassant    les    limites    applicables    aux   
appareils    numeriques    de    la class A  prescrites  dans le 
Reglement  sur  le  brouillage radioelectrique edicte par le ministere des 
Communications du Canada. 
 

SAVE THESE INSTRUCTIONS 

 

 

Содержание Mark Pro 2i

































































Отзывы: