Kurzweil Mark Pro 2i Скачать руководство пользователя страница 12

Страница: 12 / 64

Mark Pro TWOi

Chapter 2

Mark Pro 2i Assembly

Introduction

This chapter contains all the procedures for the disassembly and reassembly of Mark Pro 2i as

well as instruments with factory-installed. There are three main sections: Opening the Mark Pro

2i, Top Enclosure, Mark Pro 2 Keyboard Assembly.

Warning

: If possible, save all user programs and setups before disassembly. For instructions.

Notes, Cautions, Warnings

Please pay special attention to all Notes, Cautions, and Warnings as they not only point out

specific instructions.

Cables, Connectors

Flat Ribbon Cables

All flat ribbon cables with connectors are keyed, and therefore cannot be reversed. Most flat

ribbon cables have locking cable clips. Be sure to reapply the clips when connecting cables.

When disconnecting and connecting these cables, you must look for the marking on the edge of

the cable denoting Pin 1 and be sure that you match it correctly with Pin 1 on the board.

Cable Routing

In some cases, tape secures cable connections or fastens cables to the Top enclosure. Always

peel back the tape from one side when disconnecting cables so that the tape remains properly

positioned.

Required Tools and Materials

screwdriver

Содержание Mark Pro 2i

































































Результаты поиска

Содержание Mark Pro 2i

Отзывы:

Бренды по названию

Популярные бренды

Kurzweil Mark Pro 2i, Руководство по обслуживанию

Результаты поиска

Содержание Mark Pro 2i

Отзывы:

Бренды по названию

Популярные бренды