background image

14

All Kurt Manufacturing Company industrial workholding products and parts 
with the exceptions noted below, are warranted against  defects in material and 
workmanship for the life of the product or part.  (The life of the product is defined 
as that point in time when such item no longer functions due to normal wear 
and tear.)   Failure to properly maintain and/or properly operate the product or 
part that has been worn out, abused, heated, ground or otherwise altered, used 
for a purpose other than that for which it was intended, or used in a manner in 
consistent with any instructions regarding its use.  The sole obligation of Kurt 
Manufacturing Company, Inc. (Kurt) and the purchaser’s SOLE AND EXCLUSIVE 
REMEDY hereunder, shall be limited to the replacement or repair of any Kurt 
product or part (by an authorized Kurt technician) which are returned to Kurt 
Manufacturing Company’s place of business or any authorized service center, 
transportation, shipping and postal charges prepaid, and there determined by  
Kurt Manufacturing Company to be covered by the warranty contained herein.

THE LIMITED WARRANTY DESCRIBED HEREIN IS MADE EXPRESSLY IN LIEU OF 
ANY OTHER EXPRESSED OR IMPLIED WARRANTIES, INCLUDING ANY IMPLIED 
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
KURT MANUFACTURING COMPANY IS NOT RESPONSIBLE FOR THE IMPROPER 
USE OF ITS PRODUCTS.  KURT SHALL NOT BE LIABLE FOR ANY DIRECT, 
INDIRECT, INCIDENTAL SPECIAL OR CONSEQUENTIAL DAMAGES, INCLUDING 
BUT NOT LIMITED TO, LOSS OF USE, REVENUE OR PROFIT.

KURT ASSUMES NO LIABILITY FOR, AND MAKES NO WARRANTY REGARDING 
ANY PURCHASE ITEMS WHERE THE MANUFACTURER OF SUCH ITEM  EXTENDS 
A SEPARATE WARRANTY.

WARRANTY

Содержание MaxLock PF420C
















Отзывы: