22
EEB 6100.0
The electronic timer with
switch-off function
Setting the clock
F
The clock must be set before first using the oven or after a loss of power
(mains). The oven will not function until the clock is set.
If the clock is not set, a dash flashes in the bottom right-hand corner of
the display.
F
Would you like to change the preset time?
Proceed exactly as follows.
– Press the middle button twice.
A dash flashes on the right-hand side of
the display.
– Immediately set the desired time with
the “+” and “-” keys. The clock starts
after a few seconds and the flashing
dash disappears.
Setting the alarm time
F
If the oven is switched on the timer has a switch-off function: If the timer
runs down the oven switches off. If the oven is not operating the timer
can be used as “reminder”.
– Press the middle button once.
A dash flashes on the left-hand side of
the display, “0.00” appears in the
display.
– Use “+”/“-” to set the timer in hours
and minutes.
After a short time the dash comes on
permanently and the preset time starts
to run.
After the time has run down a signal rings and the oven switches automatically
off. “0.00” appears in the display and the dash flashes.
– Press one of the keys to turn off the signal. The is switched on again.
F
If the signal is not turned off it stops after approx. 2 min. by itself. The
oven stays off until you convert the oven into the normal mode by
pressing one of the keys.
Cleaning and care
You should carefully read this chapter before you use your appliance the first
time. If cleaned correctly and looked after regularly the appliance will remain
beautiful and clean for many years. Here you will find tips concerning the
careful cleaning and of the individual surfaces and how to look after them.
For all surfaces
[
Steam and/or pressure cleaning machines must not be used to clean the
appliance! This can damage the unit resulting in risk of
personal injury
.
[
Risk of burning!
Make sure the appliance has cooled down before
cleaning.
[
Please note the instructions of the cleaning agents.
Clean the appliance each time you use it. Not removed dirt will burn into the
surface the next time you switch it on and these incrustations can often not
be removed anymore.
Use a damp cloth or a soft sponge with warm water containing a small amount
of detergent to clean light amounts of dirt from the surface. Always wipe off
the surface completely with cold water to remove cleaning agents residues
which could cause discolouring and stains. Wipe dry afterwards.
F
You can find information in the following paragraphs concerning the
individual surfaces and parts and how to remove heavy dirt.
F
VSR O-FIX-C is perfect for the cleaning of glass ceramic, enamel and the
coated inside of the door. You can obtain this cleaning agent from
KÜPPERSBUSCH customer service.
Do not use any
- aggressive or bleaching cleaning agents containing for example active
oxygen, chlorine or corrosive components.
- abrasive or aggressive cleaning or scouring agents such as steel wool,
soap-impregnated steel wool, metal or plastic sponges or similar agents
with an abrasive surface.
Remove caking
Heavy dirt should first be soaked – best with a wet cloth. Afterwards it is easier
to remove the dirt.
Please note the information for the cleaning
scraper
[
Caution! Risk of cutting! The blade of the cleaning scraper is very sharp!
Always keep the cleaning scraper flat on the
surface and push the caking away.
[
Do not scratch the surface with the edge of
the scraper and take care not to damage the
sealings with the edge.
The use of oven sprays - information
[
Pease follow the instructions of the manufacturer. Oven sprays damage
aluminium, lacquered surfaces and plastic!
[
Do not spray into the opening of the ventilator at the backplate!
For environmental reasons you should not use oven spray at all. If you
nevertheless want to use it, only spray it in the oven interior and on enamel
baking trays.
